Skip to content

mohitmishra786/low-level-dev-skills / skills/baremetal/stm32-baremetal

stm32-baremetal

Verified

STM32 bare-metal skill for CMSIS-only MCU projects. Use when scaffolding STM32 firmware without HAL, configuring clocks/RCC, using CMSIS headers, or building with arm-none-eabi-gcc. Activates on queries about STM32 bare metal, CMSIS without HAL, STM32F4/H7 bring-up, or minimal Makefile CMake for Cortex-M.

STM32 Bare-Metal (CMSIS, No HAL)

Purpose

Guide agents through a minimal STM32 bare-metal project using CMSIS device headers and startup code only — no STM32 HAL — covering clock setup, linker script integration, peripheral register access, and a reproducible build layout for STM32F/G/H/L families.

Triggers

  • Starting STM32 firmware without Cube HAL dependency
  • Porting vendor examples to register-level drivers
  • Integrating with skills/baremetal/baremetal-startup and skills/embedded/linker-scripts
  • Debugging clock or flash placement issues on STM32
  • Teaching register-level STM32 before RTOS or Zephyr

Workflow

1. Minimal project layout

stm32-bare/
├── startup_stm32f407xx.s   # vector table + Reset_Handler
├── system_stm32f4xx.c      # SystemInit(), SystemCoreClockUpdate()
├── stm32f407xx.h           # CMSIS (from ST pack or copy)
├── linker.ld               # FLASH/RAM regions
├── main.c
└── Makefile

Use CMSIS-Core (core_cm4.h) and device header from ST CMSIS pack or open-source packs (e.g. stm32-cmsis-device-f4).

2. Clock configuration (RCC)

STM32 requires explicit HSE/HSI and PLL setup before high-speed peripherals:

/* system_stm32f4xx.c — simplified PLL from 8 MHz HSE */
void SystemInit(void)
{
    RCC->CR |= RCC_CR_HSEON;
    while (!(RCC->CR & RCC_CR_HSERDY)) {}

    /* M=8, N=336, P=2, Q=7: VCO 336 MHz, SYSCLK 168 MHz, USB/SDIO 48 MHz */
    RCC->PLLCFGR = RCC_PLLCFGR_PLLSRC_HSE | (8 << 0) | (336 << 6) | (0 << 16) | (7 << 24);
    /* AHB 168 MHz, APB1 42 MHz (max 42), APB2 84 MHz (max 84) */
    RCC->CFGR   |= RCC_CFGR_HPRE_DIV1 | RCC_CFGR_PPRE1_DIV4 | RCC_CFGR_PPRE2_DIV2;
    RCC->CR     |= RCC_CR_PLLON;
    while (!(RCC->CR & RCC_CR_PLLRDY)) {}

    FLASH->ACR = FLASH_ACR_LATENCY_5WS;
    RCC->CFGR  |= RCC_CFGR_SW_PLL;
    while ((RCC->CFGR & RCC_CFGR_SWS) != RCC_CFGR_SWS_PLL) {}

    SystemCoreClockUpdate();
}

Always match FLASH_ACR wait states to voltage scale and SYSCLK per reference manual table. Check the APB prescalers against the bus limits in the datasheet (STM32F405/407: APB1 42 MHz, APB2 84 MHz). On F405/407, timers on a divided APB bus run at twice the APB clock, so APB1 timers get 84 MHz here. F42x/F43x add RCC_DCKCFGR.TIMPRE, which changes the multiplier to x4 for some prescalers; check the timer clock table in the reference manual for other parts.

3. Enable peripheral clock before MMIO

#define RCC_AHB1ENR_GPIOAEN (1U << 0)

static inline void gpioa_clock_enable(void)
{
    RCC->AHB1ENR |= RCC_AHB1ENR_GPIOAEN;
    (void)RCC->AHB1ENR; /* AHB read-after-write — required on STM32 */
}

4. Build flags (arm-none-eabi-gcc)

MCU      = -mcpu=cortex-m4 -mthumb -mfpu=fpv4-sp-d16 -mfloat-abi=hard
CFLAGS   = $(MCU) -Wall -Wextra -ffunction-sections -fdata-sections -g3
LDFLAGS  = $(MCU) -T linker.ld -Wl,--gc-sections -specs=nano.specs -lc -lm -lnosys

5. Flash map (typical F4)

RegionAddressNotes
Flash0x08000000Vector table at boot
SRAM10x20000000Stack, heap, .data/.bss
CCM0x10000000F4 only — not DMA-accessible from all masters

Bootloader apps often link at 0x08010000 and set SCB->VTOR = 0x08010000 on entry.

6. QEMU note

QEMU STM32 machines (stm32vldiscovery, netduinoplus2, etc.) use different MCUs than F407 and omit GPIO/DMA/I2C per QEMU STM32 docs. Use skills/qemu/qemu-embedded-simulation for simulation; validate F4 firmware on hardware.

7. Agent usage

/stm32-baremetal Scaffold CMSIS-only STM32F407 project with USART2 printf

Common Problems

SymptomCauseFix
Hang in SystemInitHSE not populated / wrong PLLUse HSI for bring-up; verify crystal
Peripheral deadRCC clock gate offEnable AHB/APB bit; read-back RCC
HardFault on bootStack in wrong region / VTORCheck _estack in linker.ld
Wrong baud rateSystemCoreClock staleCall SystemCoreClockUpdate() after PLL
DMA fails from CCMCCM not on AHB matrix pathPlace DMA buffers in SRAM1

Related skills

  • skills/baremetal/baremetal-startup — vector table and .data/.bss
  • skills/baremetal/mmio-and-bit-manipulation — register access patterns
  • skills/baremetal/bootloaders-embedded — app offset and VTOR relocation
  • skills/embedded/linker-scripts — FLASH/RAM MEMORY blocks
  • skills/embedded/openocd-jtag — flash and GDB via ST-Link
reverse-engineer-anythingmorluto/reaReverse engineer native, managed, Electron/JavaScript, packaged, firmware, and browser targets with REA, and build agent environments (AgentEnv bundles) of web applications from a live instance or a capture, and of Linux desktop apps with a task from a request. Use shipped-artifact or requested runtime evidence to explain features, compare versions, decompile code, or guide a reconstruction. Skip REA for ordinary source-repository architecture analysis.Stars: 471kUpdated Claude CodeCodexVerifiedInstall
diagnosing-superpowersobra/superpowersUse when a superpowers session went wrong and your human partner wants to know why — repeated work, ignored plans, stumbles, poor results, a skill that didn't fire, "it took too long", "why is it so expensive", "what is it doing" — or wants to build a bug report for the superpowers maintainers, for the current session or a past one identified by id or path, on any harness.Stars: 322kUpdated Claude CodeCodexVerifiedInstall
dispatching-parallel-agentsobra/superpowersUse when facing 2+ independent tasks that can be worked on without shared state or sequential dependenciesStars: 322kUpdated Claude CodeCodexVerifiedInstall
executing-plansobra/superpowersUse when executing an implementation plan in the current session as the implementer yourself — your human partner chose inline execution, or no subagent tool is availableStars: 322kUpdated Claude CodeCodexVerifiedInstall