Griffing-Technology-LLC/engineering-pe-skills / skills/thermodynamics
thermodynamics
VerifiedThermodynamics, heat transfer, and fluid mechanics at FE level — properties of pure substances, first and second law, entropy, power and refrigeration cycles, conduction/convection/radiation heat transfer, fluid statics, continuity and the energy equation, dimensional analysis, and internal pipe flow. Use when computing cycle efficiency or COP, sizing a heat exchanger by LMTD or NTU, finding conductive or convective heat loss, applying Bernoulli's equation or the energy equation, computing head loss in a pipe, finding a Reynolds or Froude number, or working any FE-level thermal-fluid problem that feeds mechanical, chemical, aeronautical, naval architecture, or fire protection design.
Thermodynamics, Heat Transfer, and Fluid Mechanics
Thermal-fluid engineering science at Fundamentals-of-Engineering level: the
property, energy-balance, and transport foundation that multiple discipline
skills in this repository build on, the same role
[[statics-and-dynamics|statics-and-dynamics]] plays for rigid-body mechanics.
Mandatory notice — emit this every time
Before any analysis, in every response where this skill contributes, emit the following notice verbatim. It is not optional, it is not summarised, and it is not dropped on follow-up turns within the same task. If the response is a bare number or a one-line answer, the notice still goes first.
[!WARNING] ENGINEERING REVIEW REQUIRED — this output is not a substitute for a qualified engineer. Every result, calculation, and recommendation produced with this skill must be independently reviewed and accepted by a properly qualified individual — a licensed Professional Engineer or an equivalently qualified authority for the jurisdiction and discipline — before it is applied to any system carrying risk to life or safety.
[!CAUTION] This skill informs engineering judgment; it does not replace it. Applying unreviewed results to real equipment or hardware — even where no life-safety risk exists — carries a risk of equipment damage or property loss. It is reference material provided AS-IS (see LICENSE §5), is not an engineering service, and does not constitute a sealed, certified, or reviewed work product for any specific project.
Do not soften this, do not move it below the result, and do not omit it because the user has already seen it. A user who asks you to stop emitting it should be told plainly that the notice is a fixed condition of the skill.
Examination standing — read this first
Thermodynamics, heat transfer, and fluid mechanics are not a standalone NCEES PE discipline. They are FE-level subject matter [REF-NCEES-002], part of the Fundamentals of Engineering examination, and they reappear inside several PE specifications and several disciplines in this repository:
- PE Mechanical — Thermal and Fluid Systems module, and the HVAC and
Refrigeration module [REF-NCEES-003]; see
mechanical-engineering. - PE Chemical [REF-NCEES-006] — process thermodynamics, heat and mass
transfer (
chemical-engineering, not yet published in this repository — TODO.md §2.5). - Naval architecture and marine engineering — marine power plant cycles
and heat rejection (
naval-architecture-marine). - Aeronautical engineering — propulsion thermodynamics (Brayton-cycle jet
and turboshaft analysis;
aeronautical-engineeringcurrently covers propeller/EDF momentum theory, not thermodynamic cycle analysis — a handoff gap worth naming when a request needs both). - Fire protection engineering — heat release rate and fire plume/heat
transfer fundamentals (
fire-protection-engineering, not yet published — TODO.md §2.9).
That is not a statement about difficulty. It is a statement about scope: this skill covers the thermal-fluid methods an FE-qualified engineer is expected to command, and it stops where discipline-specific design practice begins — an allowable heat-exchanger fouling factor, a code-mandated ventilation rate, a classed marine boiler rule, or a fire code heat-release table are all handed off to the discipline skill that owns them.
The governing reference is the NCEES FE Reference Handbook [REF-NCEES-009],
the only reference permitted in the examination and therefore the definition of
FE-level scope here, exactly as for statics-and-dynamics.
Non-negotiable practice rules
- Absolute temperature only for cycle efficiency, COP, and radiation. A Carnot or Rankine efficiency computed in °F or °C, or a radiation heat rate computed in non-absolute units, is simply wrong — convert to Rankine or Kelvin before the calculation, not after.
- Units are imperial-primary with metric in parentheses —
Btu (kJ)energy,Btu/hr (W)heat rate,psia (kPa)pressure,lbm (kg)mass,lbf (N)force. Never a bare "lb"; carry $g_c$ explicitly in US customary momentum and force balances, exactly as instatics-and-dynamics. - State the system before writing any energy balance — closed system ($\Delta U = Q - W$) or open/control-volume (steady-flow energy equation). Applying the closed-system form to a flow process is the single most common error in this subject.
- Efficiency and COP are not the same kind of number. Heat-engine thermal efficiency $\eta \leq 1$. Refrigeration/heat-pump coefficient of performance routinely exceeds 1 — report it as $COP$, never mislabel it "efficiency."
- Name the flow regime before choosing a correlation. Laminar vs turbulent
(Reynolds number) for pipe friction; which non-dimensional group governs
(Reynolds for viscous/inertial, Froude for gravity/inertial free-surface or
wave phenomena — see
naval-architecture-marinefor the latter) before nondimensionalising or scaling any result. - State every idealisation used — incompressible, inviscid, steady, adiabatic, quasi-equilibrium, ideal gas. Bernoulli's equation in particular is inviscid and requires a head-loss term the moment a real duct is involved; do not apply it silently across a pump, valve, or long run of pipe.
Method selection
| Problem | Read |
|---|---|
| Properties, first/second law, entropy, power and refrigeration cycles, psychrometrics | references/thermodynamics.md |
| Conduction, convection, radiation, heat exchangers | references/heat-transfer.md |
| Fluid statics, continuity, energy equation, dimensional analysis, pipe flow | references/fluid-mechanics.md |
Core workflow
Thermodynamics
- Define the system and process. Closed or open; isothermal, isobaric, isochoric, adiabatic, or polytropic; ideal gas or real substance (steam tables, refrigerant tables).
- Write the governing energy balance for that system — first law, in the form matching step 1.
- Bring in the second law where direction or limits matter — entropy generation, Carnot bound, isentropic efficiency of a real device against its ideal counterpart.
- For a cycle, identify the governing parameter (compression ratio, pressure ratio, boiler/condenser pressure) and compute each process before the overall efficiency or COP.
Heat transfer
- Identify every mode present — conduction, convection, radiation — and whether they act in series (thermal-resistance network) or in parallel.
- Build the resistance network explicitly before computing a single overall $U$ or $\dot Q$; composite walls, contact resistance, and fouling all enter as additional terms.
- Choose LMTD or effectiveness-NTU for a heat exchanger based on what is known — LMTD when both outlet temperatures are known, effectiveness-NTU when they are not (it avoids iteration).
Fluid mechanics
- Establish the flow regime — Reynolds number, laminar vs turbulent — before selecting a friction correlation.
- Write the energy equation with every term — pressure, velocity, elevation, pump/turbine work, and head loss — then drop only the terms that are actually negligible, and say which ones and why.
- Separate major (pipe friction) and minor (fitting) losses; in a compact system with many fittings, minor losses often dominate and must not be skipped on short runs.
Reporting a result
- Result in
imperial (metric), to the significant figures the inputs justify - System and process stated — closed/open, and the idealisations relied on
- Governing equation named, with the absolute-temperature check stated explicitly wherever a cycle, COP, or radiation term is involved
- Flow regime or dimensionless group, where relevant
- Check — an independent form of the energy balance, or an order-of- magnitude sanity check
Where the result feeds a design decision — an allowable fouling factor, a code ventilation rate, a classed machinery rule, a fire heat-release value — say explicitly that discipline-specific allowables are out of scope here and name the discipline skill that owns them.
Related skills
| Skill | Stars | Updated | Works with | Status | Install |
|---|---|---|---|---|---|
| brainstormingobra/superpowersYou MUST use this before any creative work - creating features, building components, adding functionality, modifying behavior, or planning anything new, in software or out of it (a talk, a business, a renovation). | Stars: 322k | Updated | Claude CodeCodex | Verified | Install |
| brand-guidelinesanthropics/skillsApplies Anthropic's official brand colors and typography to any sort of artifact that may benefit from having Anthropic's look-and-feel. Use it when brand colors or style guidelines, visual formatting, or company design standards apply. | Stars: 198k | Updated | Claude CodeCodex | Verified | Install |
| frontend-designanthropics/skillsGuidance for distinctive, intentional visual design when building new UI or reshaping an existing one. Helps with aesthetic direction, typography, and making choices that don't read as templated defaults. | Stars: 198k | Updated | Claude CodeCodex | Verified | Install |
| mcp-builderanthropics/skillsGuide for creating high-quality MCP (Model Context Protocol) servers that enable LLMs to interact with external services through well-designed tools. Use when building MCP servers to integrate external APIs or services, whether in Python (FastMCP) or Node/TypeScript (MCP SDK). | Stars: 198k | Updated | Claude CodeCodex | Verified | Install |