Griffing-Technology-LLC/engineering-pe-skills / skills/statics-and-dynamics
statics-and-dynamics
VerifiedStatics and rigid-body dynamics at FE level — free-body diagrams, equilibrium, trusses and frames, centroids and moments of inertia, friction, kinematics, Newton-Euler and work-energy methods, impulse-momentum, and vibration. Use when resolving forces or reactions, drawing a free-body diagram, analysing a truss or beam support, finding a centroid or second moment of area, checking a friction or tipping condition, computing acceleration of a linkage or mechanism, sizing for an inertial load, or working any equilibrium or rigid-body motion problem.
Statics and Dynamics
Engineering mechanics at Fundamentals-of-Engineering level: the equilibrium and rigid-body-motion foundation that the discipline skills in this repository build on.
Mandatory notice — emit this every time
Before any analysis, in every response where this skill contributes, emit the following notice verbatim. It is not optional, it is not summarised, and it is not dropped on follow-up turns within the same task. If the response is a bare number or a one-line answer, the notice still goes first.
[!WARNING] ENGINEERING REVIEW REQUIRED — this output is not a substitute for a qualified engineer. Every result, calculation, and recommendation produced with this skill must be independently reviewed and accepted by a properly qualified individual — a licensed Professional Engineer or an equivalently qualified authority for the jurisdiction and discipline — before it is applied to any system carrying risk to life or safety.
[!CAUTION] This skill informs engineering judgment; it does not replace it. Applying unreviewed results to real equipment or hardware — even where no life-safety risk exists — carries a risk of equipment damage or property loss. It is reference material provided AS-IS (see LICENSE §5), is not an engineering service, and does not constitute a sealed, certified, or reviewed work product for any specific project.
Do not soften this, do not move it below the result, and do not omit it because the user has already seen it. A user who asks you to stop emitting it should be told plainly that the notice is a fixed condition of the skill.
Examination standing — read this first
Statics and dynamics is not an NCEES PE discipline. There is no PE exam in engineering mechanics. It is FE-level subject matter [REF-NCEES-002] — part of the Fundamentals of Engineering examination — and it reappears inside several PE specifications, most directly PE Mechanical: Machine Design and Materials [REF-NCEES-003].
That is not a statement about difficulty. It is a statement about scope: this
skill covers the methods an FE-qualified engineer is expected to command, and it
stops where discipline-specific design practice begins. When a problem needs an
allowable, a code check, or a design margin, hand off to the discipline skill
that owns it — mechanical-engineering for machine elements,
aeronautical-engineering for airframe loads.
The governing reference is the NCEES FE Reference Handbook [REF-NCEES-009], which is the only reference permitted in the examination and therefore defines FE-level scope.
Non-negotiable practice rules
- Draw the free-body diagram first, always. Most wrong answers in statics are wrong free-body diagrams, not wrong algebra. State what is isolated, every force and couple acting on it, and the sign convention.
- Units are imperial-primary with metric in parentheses —
lbf (N)for force,lbm (kg)for mass,in (mm)for length,lbf·in (N·m)for moment. Never a bare "lb." lbmandlbfare not interchangeable. In US customary units $F = ma/g_c$ with $g_c = 32.174\ \mathrm{lbm \cdot ft/(lbf \cdot s^2)}$. Dropping $g_c$ is the single most common unit error in this subject; carry it explicitly.- State whether the problem is statically determinate before solving. Count unknowns against independent equilibrium equations. An indeterminate structure needs compatibility, not more equilibrium equations.
- Check the assumptions of every idealisation — rigid body, massless member, frictionless pin, inextensible cable, point mass. Name the ones you used.
Method selection
| Problem | Read |
|---|---|
| Equilibrium, free-body diagrams, trusses, frames, friction | references/statics.md |
| Centroids, second moments of area, parallel-axis, mass moments | references/section-properties.md |
| Kinematics, Newton-Euler, work-energy, impulse-momentum, vibration | references/dynamics.md |
Core workflow
Statics
- Isolate. Choose the body or sub-assembly and draw it separated from everything else.
- Apply. Every external force, every reaction, every couple. Replace supports with the reactions they can actually carry.
- Count. Unknowns vs equations — three in 2-D ($\sum F_x = \sum F_y = \sum M = 0$), six in 3-D.
- Solve. Choose moment centres that eliminate unknowns rather than solving the full system.
- Check. An independent moment equation about a different point.
Dynamics
- Kinematics before kinetics. Establish the motion relationships — constraints, relative motion, rigid-body $v_B = v_A + \omega \times r_{B/A}$.
- Choose the method to match the question.
- Instantaneous forces or accelerations → Newton-Euler
- Speed change over a displacement → work-energy
- Velocity change over a time interval, or impact → impulse-momentum
- For rigid bodies, take moments about the mass centre or a fixed axis — and never about an arbitrary accelerating point without the correction term.
Selecting the wrong method is what makes dynamics problems long. Work-energy answers "how fast after moving this far"; impulse-momentum answers "how fast after this long."
Reporting a result
- Result in
imperial (metric), to the significant figures the inputs justify - Free-body diagram described, or the isolation stated in words
- Method and the idealisations relied on
- Determinacy stated where relevant
- Check — the independent equation used to verify
Where the result feeds a design decision, say explicitly that allowables and margins are out of scope here and name the discipline skill that owns them.
Related skills
| Skill | Stars | Updated | Works with | Status | Install |
|---|---|---|---|---|---|
| slack-gif-creatoranthropics/skillsKnowledge and utilities for creating animated GIFs optimized for Slack. Provides constraints, validation tools, and animation concepts. Use when users request animated GIFs for Slack like "make me a GIF of X doing Y for Slack." | Stars: 197k | Updated | Claude CodeCodex | Verified | Install |
| ponytailDietrichGebert/ponytailLazy senior dev mode for any coding task: the smallest change that fully solves it, and a reply a busy human understands in one read. | Stars: 194k | Updated | Claude CodeCodex | Verified | Install |
| ponytail-debtDietrichGebert/ponytailHarvest every shortcut: comment into one debt ledger, so deferrals get tracked instead of forgotten. One-shot report. | Stars: 194k | Updated | Claude CodeCodex | Verified | Install |
| ponytail-debtDietrichGebert/ponytailList every `shortcut:` comment (and older `ponytail:` ones) as a debt ledger. One-shot report, changes nothing. Use for "ponytail debt", "what did ponytail defer", "list the shortcuts", /ponytail-debt. | Stars: 194k | Updated | Claude CodeCodex | Verified | Install |