Skip to content

Griffing-Technology-LLC/engineering-pe-skills / skills/mechanical-engineering

mechanical-engineering

Verified

Mechanical engineering design and analysis aligned to the NCEES PE Mechanical exam — machine design, stress and fatigue, shafts, bearings, gears, fasteners and bolted joints, springs, thermodynamic cycles, heat transfer, fluid systems and pumps, and HVAC. Use when sizing a shaft or bearing, checking a bolted joint or weld, computing stress concentration or fatigue life, selecting a gear or belt drive, sizing a pump or duct, analysing a thermodynamic cycle or heat exchanger, doing a thermal or pressure-vessel check, or applying ASME codes.

Mechanical Engineering

Machine design, thermal, and fluid-systems analysis aligned to the NCEES PE Mechanical examination, with every method traceable to a cited authority.

Mandatory notice — emit this every time

Before any analysis, in every response where this skill contributes, emit the following notice verbatim. It is not optional, it is not summarised, and it is not dropped on follow-up turns within the same task. If the response is a bare number or a one-line answer, the notice still goes first.

[!WARNING] ENGINEERING REVIEW REQUIRED — this output is not a substitute for a qualified engineer. Every result, calculation, and recommendation produced with this skill must be independently reviewed and accepted by a properly qualified individual — a licensed Professional Engineer or an equivalently qualified authority for the jurisdiction and discipline — before it is applied to any system carrying risk to life or safety.

[!CAUTION] This skill informs engineering judgment; it does not replace it. Applying unreviewed results to real equipment or hardware — even where no life-safety risk exists — carries a risk of equipment damage or property loss. It is reference material provided AS-IS (see LICENSE §5), is not an engineering service, and does not constitute a sealed, certified, or reviewed work product for any specific project.

Do not soften this, do not move it below the result, and do not omit it because the user has already seen it. A user who asks you to stop emitting it should be told plainly that the notice is a fixed condition of the skill.

Examination standing

Aligned to PE Mechanical [REF-NCEES-003], which NCEES offers in three modules — a candidate sits one:

ModuleScope
HVAC and RefrigerationPsychrometrics, loads, air and water distribution, refrigeration cycles
Machine Design and MaterialsStress, fatigue, machine elements, materials, joints
Thermal and Fluid SystemsCycles, heat transfer, fluid mechanics, pumps and piping

The exam is 80 questions across a 9-hour appointment; NCEES supplies the electronic reference handbook and all specified design standards. Note that because no PE exam exists for aeronautical engineering, this is also the usual licensure route for engineers doing aircraft structural and propulsion work — see aeronautical-engineering for that discipline's standing.

The principal standards-developing organisation is ASME [REF-SOC-004], publisher of the Boiler & Pressure Vessel Code, ASME Y14.5 (GD&T), and the ASME B-series dimensional standards.

Non-negotiable practice rules

  1. Units are imperial-primary with metric in parentheses. lbf (N) force, lbm (kg) mass, psi (MPa) stress, Btu/hr (W) heat rate. Never a bare "lb"; carry $g_c$ explicitly in US customary dynamics.
  2. Every allowable is cited. Yield, ultimate, endurance limit, allowable stress — each comes from a material specification, a code table, or test data with a REF-ID. A remembered allowable is not an allowable.
  3. Name the failure mode. Yield, ultimate, buckling, fatigue, creep, fretting, thread stripping, bearing, tear-out. A margin without a named failure mode is meaningless, and the governing mode is often not the obvious one.
  4. State the factor of safety and where it came from — a code, a company standard, or an engineering judgment you are declaring.
  5. Anisotropic and additively manufactured materials are not isotropic metals. Do not apply isotropic machine-design formulae to printed polymer without saying what that costs. See references/materials-and-fatigue.md.

Method selection

ProblemRead
Stress, stress concentration, fatigue, failure theories, allowablesreferences/materials-and-fatigue.md
Shafts, bearings, gears, springs, bolted joints, weldsreferences/machine-elements.md
Cycles, heat transfer, fluid systems, pumps, HVACreferences/thermal-and-fluids.md

Core workflow

  1. Define the load case. Magnitude, direction, and whether it is static, fluctuating, or impact. Fatigue is governed by the alternating component and the mean stress, not the peak alone.
  2. Establish geometry and stress state. Nominal stress, then the stress concentration factor $K_t$ at every discontinuity — fillets, holes, keyways, thread roots. For fatigue, apply the notch sensitivity to get $K_f$.
  3. Select the failure theory appropriate to the material:
    • Ductile, static → distortion energy (von Mises) or maximum shear
    • Brittle, static → maximum normal stress or a modified Mohr theory
    • Fluctuating → a mean-stress criterion (Goodman, Gerber, Soderberg), stated by name
  4. Get the allowable from a cited source, corrected for the real part — surface finish, size, loading type, temperature, reliability.
  5. Compute the margin and name the failure mode it is against.
  6. Check the modes you did not compute. Buckling on anything slender, deflection where fit matters, and the joint rather than the member — parts usually fail at their connections.

Reporting a result

  • Result in imperial (metric), to justified significant figures
  • Load case and whether static or fluctuating
  • Stress state and the concentration factors applied
  • Failure theory named
  • Allowable with its source
  • Margin, with its failure mode
  • Modes checked and found non-governing, so the reader knows what was ruled out rather than overlooked
brainstormingobra/superpowersYou MUST use this before any creative work - creating features, building components, adding functionality, modifying behavior, or planning anything new, in software or out of it (a talk, a business, a renovation).Stars: 321kUpdated Claude CodeCodexVerifiedInstall
brand-guidelinesanthropics/skillsApplies Anthropic's official brand colors and typography to any sort of artifact that may benefit from having Anthropic's look-and-feel. Use it when brand colors or style guidelines, visual formatting, or company design standards apply.Stars: 197kUpdated Claude CodeCodexVerifiedInstall
frontend-designanthropics/skillsGuidance for distinctive, intentional visual design when building new UI or reshaping an existing one. Helps with aesthetic direction, typography, and making choices that don't read as templated defaults.Stars: 197kUpdated Claude CodeCodexVerifiedInstall
mcp-builderanthropics/skillsGuide for creating high-quality MCP (Model Context Protocol) servers that enable LLMs to interact with external services through well-designed tools. Use when building MCP servers to integrate external APIs or services, whether in Python (FastMCP) or Node/TypeScript (MCP SDK).Stars: 197kUpdated Claude CodeCodexVerifiedInstall