Griffing-Technology-LLC/engineering-pe-skills / skills/aeronautical-engineering
aeronautical-engineering
VerifiedAeronautical and aerospace engineering analysis with authoritative citations — airfoil and wing aerodynamics, lift/drag/moment build-up, propeller and EDF thrust, weight and balance, CG and static margin, V-n envelopes, and airframe load factors. Use when sizing a wing, computing lift or drag, analysing an airfoil or aerofoil section, checking CG or static margin, building a V-n diagram, sizing a propeller or ducted fan, doing a weight-and-balance or mass-properties roll-up, or evaluating a UAS or light aircraft airframe against FAA Part 23/107, NASA, or ASTM F38 standards.
| File | Kind | Size |
|---|---|---|
| SKILL.md | skill md | 9.0 KB |
| references/aerodynamics.md | markdown | 4.5 KB |
| references/loads-and-factors.md | markdown | 8.2 KB |
| references/propulsion.md | markdown | 3.1 KB |
| references/weight-and-balance.md | markdown | 3.0 KB |
references/loads-and-factors.md
View on GitHub# Loads, Factors of Safety, and the V-n Envelope
Reference file for the `aeronautical-engineering` skill. Read before working any
structural load, factor-of-safety, or flight-envelope problem.
## Contents
1. Limit, ultimate, and the factor between them
2. The V-n manoeuvre envelope
3. Gust loads
4. Adopting criteria when none are imposed
5. Margin of safety reporting
6. Threaded joints
---
## 1. Limit, ultimate, and the factor between them
Three distinct quantities, routinely confused:
| Term | Definition |
| --- | --- |
| **Limit load** | The maximum load expected in service. Structure must carry it with no detrimental permanent deformation. |
| **Ultimate load** | Limit load × factor of safety. Structure must carry it without failure, though permanent deformation is acceptable. |
| **Factor of safety (FOS)** | The multiplier between them. |
$$P_{ult} = P_{limit} \times \mathrm{FOS}$$
The airframe factor of safety is **1.5**, and this is current regulatory text,
not folklore. 14 CFR **§23.2230** *Limit and ultimate loads* [REF-FAA-002] states
that the applicant must determine:
> "(a) The limit loads, which are equal to the structural design loads unless
> otherwise specified elsewhere in this part; and (b) The ultimate loads, which
> are equal to the limit loads multiplied by a **1.5 factor of safety** unless
> otherwise specified elsewhere in this part."
**§23.2235** *Structural strength* then requires the structure to support limit
loads without "interference with the safe operation of the airplane" or
"detrimental permanent deformation," and to support ultimate loads.
### What Part 23 does *not* give you
The 2017 restructure made Part 23 performance-based, and it did **not** carry the
old numeric manoeuvring load factors forward. **§23.2200(b)** requires only:
> "Design maneuvering load factors not less than those, which service history
> shows, may occur within the structural design envelope."
The values +3.8 and −1.52, widely quoted as "the Part 23 load factors," appear
**nowhere in the current rule** — a full-text search of the retrieved Part 23
returns zero occurrences of either number. They belong to the pre-2017 §23.337.
Citing them to current Part 23 is a fabrication. If you need numeric factors,
they come from the accepted consensus standard for the certification basis, or
from your own service-history justification under §23.2200(b).
**§23.2215** *Flight load conditions* likewise specifies the load *conditions* —
atmospheric gusts "based on measured gust statistics," symmetric and asymmetric
manoeuvres, and asymmetric thrust from a powerplant failure — without giving
gust velocities in the rule.
### Special factors of safety — the additive-manufacturing hook
**§23.2265** requires a *special* factor of safety beyond the basic 1.5 for any
part whose critical design value is uncertain, or that is:
> "(2) Subject to appreciable variability because of uncertainties in
> manufacturing processes or inspection methods."
**Printed polymer structure sits squarely in that clause.** Layer adhesion,
raster orientation, moisture, and machine-to-machine variation are exactly the
"appreciable variability" contemplated. §23.2265(c) requires the highest
pertinent special factor to multiply each limit and ultimate load. Related,
**§23.2260(b)** requires that a fabrication process needing close control be
performed under an approved process specification — which for FDM means the
print profile is part of the design record, not a shop-floor choice.
For spaceflight-derived practice, NASA-STD-5001 [REF-NASA-001] sets out a
structured factor framework distinguishing design, yield, and ultimate factors.
**Its scope is spaceflight hardware.** Applying it to an aircraft is an analogy,
and must be labelled as one every time it is used.
## 2. The V-n manoeuvre envelope
The V-n diagram bounds load factor $n$ against equivalent airspeed $V$. It is the
input to every structural load case; build it first.
Load factor is the ratio of lift to weight:
$$n = \frac{L}{W}$$
### Stall boundary
The aerodynamic limit — the aircraft cannot generate more lift than $C_{L,\max}$
allows:
$$n_{\max,aero}(V) = \frac{\tfrac{1}{2}\,\rho\,V^{2}\,S\,C_{L,\max}}{W}$$
where $\rho$ is air density, $S$ the reference wing area. This is a parabola in
$V$. Below the stall boundary the aircraft stalls before reaching the structural
limit; above it, structure governs.
### Corner speed
The manoeuvring speed $V_A$ is where the stall boundary meets the positive
structural limit $n_1$ — the lowest speed at which the limit load factor can be
reached, and therefore the highest speed at which full control deflection is
aerodynamically bounded:
$$V_A = V_S \sqrt{n_1}$$
with $V_S$ the 1-g stall speed. Both in knots.
### Envelope corners
Construct the closed envelope from:
* $V_S$ at $n = 1$
* the stall parabola out to $V_A$ at $n = n_1$
* the horizontal $n = n_1$ line out to $V_D$
* $V_D$ down to $n = 0$
* the negative-side limit $n_2$ back to the inverted stall boundary
$V_C$ (design cruise) and $V_D$ (design dive) must come from the governing
certification basis or be adopted explicitly per §4.
## 3. Gust loads
Gusts impose load factors independent of pilot input. The incremental load factor
from a sharp-edged gust of velocity $U_{de}$, with gust alleviation factor $K_g$:
$$\Delta n = \frac{K_g\,U_{de}\,V\,a\,\rho_0\,S}{2\,W}$$
where $a$ is the wing lift-curve slope $\mathrm{d}C_L/\mathrm{d}\alpha$ per radian
and $\rho_0$ sea-level density. Gust and manoeuvre envelopes are overlaid; the
governing case is whichever is outermost at each speed.
Design gust velocities $U_{de}$ and the formulation of $K_g$ are **not** in
current Part 23, which requires only that gusts be "based on measured gust
statistics" (§23.2215(a)) [REF-FAA-002]. Numeric values come from the accepted
consensus standard for the certification basis. Do not quote a gust velocity
without naming the document it came from.
## 4. Adopting criteria when none are imposed
An sUAS operated under Part 107 [REF-FAA-001] has **no imposed structural
certification basis** — Part 107 governs operations, not airworthiness. This is
the usual situation for a purpose-built unmanned airframe, and it is a trap: the
absence of an imposed criterion is not the absence of a criterion.
Adopt one deliberately and record it:
1. **State the mission envelope** — max airspeed, max manoeuvre load factor, gust
environment, and the operating weight range.
2. **Adopt limit load factors** with a stated rationale. Deriving them from the
mission ("the airframe shall sustain a 3.0 g pull-up at MTOW") is defensible;
inheriting them silently from a certification basis that does not apply is not.
3. **Adopt an FOS** and justify it. Where the structure is polymer additive
manufacture, the factor must account for anisotropy, layer adhesion, and
process variability — these are not covered by metallic-structure practice.
4. **Write all of it into the project requirements document** before sizing
anything, and cite it from the analysis.
## 5. Margin of safety reporting
$$\mathrm{MS} = \frac{\text{allowable}}{\text{applied} \times \mathrm{FOS}} - 1$$
A positive MS passes; MS = 0 is exactly critical. Report MS with:
* the **allowable** and its source (material spec, test, or cited data)
* the **applied** load and the load case it comes from
* the **FOS** applied
* the **failure mode** the margin is against
A margin quoted without its failure mode is meaningless — a part can have a large
tensile margin and fail in buckling at the same load.
## 6. Threaded joints
NASA-STD-5020 [REF-NASA-002] gives a defensible methodology for threaded
fastening systems: preload determination and uncertainty, separation margins,
and joint-slip margins. As with NASA-STD-5001, the scope is spaceflight hardware
and its use elsewhere is an analogy to be labelled.
Key discipline points regardless of source:
* Preload uncertainty is large for torque-controlled installation — carry it
explicitly rather than assuming nominal preload.
* Check **separation** and **slip** as distinct failure modes from fastener
tensile failure.
* Thread engagement length governs whether the failure is fastener tension or
thread stripping; in polymer parts, assume thread stripping governs until shown
otherwise.
Related skills
| Skill | Stars | Updated | Works with | Status | Install |
|---|---|---|---|---|---|
| slack-gif-creatoranthropics/skillsKnowledge and utilities for creating animated GIFs optimized for Slack. Provides constraints, validation tools, and animation concepts. Use when users request animated GIFs for Slack like "make me a GIF of X doing Y for Slack." | Stars: 198k | Updated | Claude CodeCodex | Verified | Install |
| ponytailDietrichGebert/ponytailLazy senior dev mode for any coding task: the smallest change that fully solves it, and a reply a busy human understands in one read. | Stars: 194k | Updated | Claude CodeCodex | Verified | Install |
| ponytail-debtDietrichGebert/ponytailHarvest every shortcut: comment into one debt ledger, so deferrals get tracked instead of forgotten. One-shot report. | Stars: 194k | Updated | Claude CodeCodex | Verified | Install |
| ponytail-debtDietrichGebert/ponytailList every `shortcut:` comment (and older `ponytail:` ones) as a debt ledger. One-shot report, changes nothing. Use for "ponytail debt", "what did ponytail defer", "list the shortcuts", /ponytail-debt. | Stars: 194k | Updated | Claude CodeCodex | Verified | Install |