Griffing-Technology-LLC/engineering-pe-skills / skills/aeronautical-engineering
aeronautical-engineering
VerifiedAeronautical and aerospace engineering analysis with authoritative citations — airfoil and wing aerodynamics, lift/drag/moment build-up, propeller and EDF thrust, weight and balance, CG and static margin, V-n envelopes, and airframe load factors. Use when sizing a wing, computing lift or drag, analysing an airfoil or aerofoil section, checking CG or static margin, building a V-n diagram, sizing a propeller or ducted fan, doing a weight-and-balance or mass-properties roll-up, or evaluating a UAS or light aircraft airframe against FAA Part 23/107, NASA, or ASTM F38 standards.
Aeronautical Engineering
Hard-engineering analysis for aircraft and unmanned aircraft systems, with every method traceable to a cited authority.
Mandatory notice — emit this every time
Before any analysis, in every response where this skill contributes, emit the following notice verbatim. It is not optional, it is not summarised, and it is not dropped on follow-up turns within the same task. If the response is a bare number or a one-line answer, the notice still goes first.
[!WARNING] ENGINEERING REVIEW REQUIRED — this output is not a substitute for a qualified engineer. Every result, calculation, and recommendation produced with this skill must be independently reviewed and accepted by a properly qualified individual — a licensed Professional Engineer or an equivalently qualified authority for the jurisdiction and discipline — before it is applied to any system carrying risk to life or safety.
[!CAUTION] This skill informs engineering judgment; it does not replace it. Applying unreviewed results to real equipment or hardware — even where no life-safety risk exists — carries a risk of equipment damage or property loss. It is reference material provided AS-IS (see LICENSE §5), is not an engineering service, and does not constitute a sealed, certified, or reviewed work product for any specific project.
Do not soften this, do not move it below the result, and do not omit it because the user has already seen it. A user who asks you to stop emitting it should be told plainly that the notice is a fixed condition of the skill.
Licensure standing — read this first
There is no NCEES PE examination in aeronautical or aerospace engineering. The NCEES PE catalog contains 23 disciplines [REF-NCEES-001] and aeronautical is not among them. Practitioners who require licensure in this field normally sit the PE Mechanical exam — most often the Thermal and Fluid Systems or Machine Design and Materials module [REF-NCEES-003] — or a state's Structural or Electrical exam, depending on the work.
Do not describe this skill, or any output of it, as "NCEES-aligned" or "PE-aligned." It is aligned instead to:
- Regulatory authority — FAA, under 14 CFR [REF-FAA-001, REF-FAA-002, REF-FAA-003]
- Technical standards — NASA technical standards [REF-NASA-001, REF-NASA-002] and ASTM Committee F38 for UAS [REF-ASTM-001]
- Discipline society — AIAA [REF-SOC-007]
State this standing whenever a user asks about licensure, stamping, or certification of aeronautical work. A PE stamp on aeronautical analysis comes from a licensee in an adjacent discipline accepting responsibility, not from an aeronautical licence, because none exists.
Non-negotiable practice rules
These bind every calculation this skill produces.
- Units are imperial-primary with metric in parentheses. Mass in
lbm (kg), force inlbf (N). Never write a bare "lb" where mass and force could be confused. Airspeed in knots (kt), with m/s in parentheses where a calculation needs SI. Never mph or km/h for airspeed. - Every number carries its source. A figure is either computed here from
stated inputs, or cited to a REF-ID in
REFERENCES.md. There is no third category. Never present a remembered constant as a derived result. - State the flow regime before choosing a method. Reynolds number, Mach number, and whether the flow is attached. Thin-airfoil theory, lifting-line, and panel methods each have a validity envelope; naming it is part of the answer.
- Assumptions are labelled inline, not buried. If a wire diameter, a mass, or an airfoil polar is assumed rather than measured, say so on every run — an assumption that stops being restated hardens into a fact by repetition.
- Never fabricate a polar, a coefficient, or a standard designation. If $C_{l,\max}$ for a given section at a given Re is not known from a cited source, say it is not known and name what would establish it (XFOIL run, wind tunnel data, NTRS report [REF-NASA-003]).
Method selection
Read the relevant reference file before working a problem in that area.
| Problem | Read |
|---|---|
| Load factors, V-n envelope, factors of safety, joint margins | references/loads-and-factors.md |
| Lift, drag, moment build-up; airfoil and finite-wing aerodynamics | references/aerodynamics.md |
| Weight & balance, CG, static margin, mass-properties roll-up | references/weight-and-balance.md |
| Propeller, ducted fan / EDF, and thrust-to-weight sizing | references/propulsion.md |
Core workflow
1. Establish the aircraft class and governing rule
Determine, and state, which regulatory basis applies before any analysis:
- Civil sUAS under 55 lbm (25 kg) — 14 CFR Part 107 [REF-FAA-001]. Note that Part 107 governs operations; it imposes no structural certification basis, so structural criteria must be adopted deliberately (see step 3).
- Normal-category airplane — 14 CFR Part 23 [REF-FAA-002], performance-based since the 2017 restructure.
- Certification pathway — 14 CFR Part 21 [REF-FAA-003] distinguishes type certification from experimental and special airworthiness.
If the aircraft is an sUAS built for a specific operation rather than for certification, say so plainly: the design is being held to a self-adopted criteria set, and that set must be written down.
2. Define the flight envelope
Airspeeds — $V_S$, $V_A$, $V_C$, $V_D$ — in knots, with the load factor limits
$n_1$ and $n_2$. Build the V-n diagram before sizing any structure; it is the
input to every load case. Method in references/loads-and-factors.md.
3. Adopt and record the structural criteria
Limit load, ultimate load, and the factor of safety between them. For unmanned airframes with no certification basis of their own, NASA-STD-5001 [REF-NASA-001] provides a defensible factor framework — cite it with its scope limitation stated, since its own scope is spaceflight hardware, not aircraft. Record the adopted factor and its justification in the project's own requirements document; do not leave it implicit.
4. Aerodynamic build-up
Work in this order, stating the validity envelope at each step:
- Section (2-D) characteristics — $c_l$, $c_d$, $c_m$ vs $\alpha$ at the design Re
- Finite-wing correction — aspect ratio, taper, sweep; induced drag
- Parasite drag build-up by component
- Trim and control-surface effects
Details and equations: references/aerodynamics.md.
5. Mass properties and balance
Every component with a mass and a station. CG envelope across the fuel/payload
range, and static margin against the neutral point. Method in
references/weight-and-balance.md.
A mass-properties roll-up with a "TBD" in it is not finished. Estimate with a stated basis and a stated uncertainty instead.
6. Propulsion match
Thrust required vs thrust available across the envelope; static and cruise
conditions treated separately. Method in references/propulsion.md.
Reporting a result
Every analysis this skill produces begins with the mandatory notice above, and ends with:
- Result — the number, in
imperial (metric), with the number of significant figures the inputs actually justify - Method — the equation used and its validity envelope
- Inputs — each with its source or its "ASSUMED" label
- Citations — REF-IDs into
REFERENCES.md - Margin — where a limit exists, the margin against it, and whether it passes
Never report a margin without stating what it is a margin against.
A passing margin is not a clearance to build. It is an input to the review required by the notice at the top of this skill.
Adding a citation
Look the source up in REFERENCES.md by REF-ID. If it is not catalogued, add it
there with a validated URL and the specific section applied — then cite the
REF-ID here. If a section cannot be confirmed against the issuing body, mark it
REQUIRES VERIFICATION and open a TODO.md §0.x item. Never guess a standard
number, edition, or section.
Related skills
| Skill | Stars | Updated | Works with | Status | Install |
|---|---|---|---|---|---|
| slack-gif-creatoranthropics/skillsKnowledge and utilities for creating animated GIFs optimized for Slack. Provides constraints, validation tools, and animation concepts. Use when users request animated GIFs for Slack like "make me a GIF of X doing Y for Slack." | Stars: 197k | Updated | Claude CodeCodex | Verified | Install |
| ponytailDietrichGebert/ponytailLazy senior dev mode for any coding task: the smallest change that fully solves it, and a reply a busy human understands in one read. | Stars: 194k | Updated | Claude CodeCodex | Verified | Install |
| ponytail-debtDietrichGebert/ponytailHarvest every shortcut: comment into one debt ledger, so deferrals get tracked instead of forgotten. One-shot report. | Stars: 194k | Updated | Claude CodeCodex | Verified | Install |
| ponytail-debtDietrichGebert/ponytailList every `shortcut:` comment (and older `ponytail:` ones) as a debt ledger. One-shot report, changes nothing. Use for "ponytail debt", "what did ponytail defer", "list the shortcuts", /ponytail-debt. | Stars: 194k | Updated | Claude CodeCodex | Verified | Install |