Griffing-Technology-LLC/engineering-pe-skills / skills/aeronautical-engineering
aeronautical-engineering
VerifiedAeronautical and aerospace engineering analysis with authoritative citations — airfoil and wing aerodynamics, lift/drag/moment build-up, propeller and EDF thrust, weight and balance, CG and static margin, V-n envelopes, and airframe load factors. Use when sizing a wing, computing lift or drag, analysing an airfoil or aerofoil section, checking CG or static margin, building a V-n diagram, sizing a propeller or ducted fan, doing a weight-and-balance or mass-properties roll-up, or evaluating a UAS or light aircraft airframe against FAA Part 23/107, NASA, or ASTM F38 standards.
| File | Kind | Size |
|---|---|---|
| SKILL.md | skill md | 9.0 KB |
| references/aerodynamics.md | markdown | 4.5 KB |
| references/loads-and-factors.md | markdown | 8.2 KB |
| references/propulsion.md | markdown | 3.1 KB |
| references/weight-and-balance.md | markdown | 3.0 KB |
references/aerodynamics.md
View on GitHub# Aerodynamics: Section, Finite Wing, and Drag Build-Up
Reference file for the `aeronautical-engineering` skill.
## Contents
1. Establish the regime first
2. Section (2-D) characteristics
3. Finite-wing correction
4. Drag build-up
5. Low-Reynolds-number practice
---
## 1. Establish the regime first
No method is valid everywhere. Before selecting one, compute and state:
**Reynolds number**, on the mean aerodynamic chord $c$:
$$\mathrm{Re} = \frac{\rho V c}{\mu} = \frac{V c}{\nu}$$
**Mach number**:
$$M = \frac{V}{a}, \qquad a = \sqrt{\gamma R T}$$
Then state the applicable method:
| Regime | Valid approach |
| --- | --- |
| $M < 0.3$ | Incompressible. Density constant. |
| $0.3 < M < 0.7$ | Prandtl–Glauert compressibility correction required |
| $M \to 1$ | Transonic; linearised corrections fail |
| $\mathrm{Re} < 5\times10^5$ | Low-Re. Laminar separation bubbles dominate; standard high-Re polars do **not** transfer |
Most small UAS operate at $\mathrm{Re} = 10^5$ to $5\times10^5$ — squarely in the
regime where textbook airfoil data taken at $\mathrm{Re} = 3\times10^6$ is
misleading. See §5.
## 2. Section (2-D) characteristics
Thin-airfoil theory gives the incompressible lift-curve slope:
$$a_0 = \frac{\mathrm{d}c_l}{\mathrm{d}\alpha} = 2\pi \ \text{per radian}$$
with zero-lift angle $\alpha_{L=0}$ set by camber. Then:
$$c_l = a_0(\alpha - \alpha_{L=0})$$
**Validity:** thin, attached, incompressible flow at small $\alpha$. It says
nothing about $c_{l,\max}$, and it cannot predict stall. $c_{l,\max}$ comes only
from cited experimental or computational data at the actual Re — never from
theory, and never from memory.
Compressibility correction (Prandtl–Glauert), valid to roughly $M = 0.7$:
$$c_{l,comp} = \frac{c_{l,inc}}{\sqrt{1 - M^{2}}}$$
## 3. Finite-wing correction
A finite wing sheds trailing vorticity, reducing effective incidence and
producing induced drag.
**Aspect ratio:**
$$AR = \frac{b^{2}}{S}$$
**Finite-wing lift-curve slope**, from lifting-line theory:
$$a = \frac{a_0}{1 + \dfrac{a_0}{\pi\,e_a\,AR}}$$
where $e_a$ is the span efficiency for lift-curve slope.
**Induced drag:**
$$C_{D_i} = \frac{C_L^{2}}{\pi\,e\,AR}$$
with Oswald efficiency $e$. For an ideal elliptical loading $e = 1$; real
straight-tapered wings run lower. **Do not assume a value for $e$** — either cite
a source for the planform in question or compute it, and label it if assumed.
**Validity:** lifting-line theory assumes high aspect ratio, unswept, attached
flow. It degrades for $AR \lesssim 4$, for significant sweep, and entirely at
stall.
## 4. Drag build-up
$$C_D = C_{D_0} + \frac{C_L^{2}}{\pi e AR}$$
$C_{D_0}$ is built up component by component — wing, fuselage, nacelles, landing
gear, antennas, and interference between them. Each component contributes:
$$C_{D_0,i} = \frac{C_{f,i}\, FF_i\, Q_i\, S_{wet,i}}{S_{ref}}$$
where $C_f$ is skin-friction coefficient, $FF$ form factor, $Q$ interference
factor, and $S_{wet}$ wetted area.
Flat-plate skin friction, turbulent:
$$C_f = \frac{0.455}{(\log_{10}\mathrm{Re})^{2.58}}$$
laminar:
$$C_f = \frac{1.328}{\sqrt{\mathrm{Re}}}$$
Each component's Re is based on **its own** reference length, not the wing chord.
Interference and form factors are empirical. Cite the source for each factor
used; if a factor is estimated, label it `ASSUMED` in the output.
## 5. Low-Reynolds-number practice
Below about $\mathrm{Re} = 5\times10^5$ the boundary layer separates laminar and
may or may not reattach. Consequences that routinely bite:
* **Published polars do not transfer.** A section characterised at
$\mathrm{Re} = 3\times10^6$ can behave qualitatively differently at $2\times10^5$
— lower $c_{l,\max}$, much higher $c_d$, and hysteresis in the stall.
* **$c_d$ can rise sharply** as Re falls, because of the separation bubble rather
than skin friction.
* **Surface finish and trip location matter** more than at high Re. On an additively
manufactured wing, layer lines are a de-facto trip strip whose effect is
real and usually uncharacterised — say so rather than ignoring it.
Get section data from one of:
* **XFOIL / panel + integral boundary layer** at the actual Re — appropriate for
attached and mildly separated flow; unreliable through stall
* **RANS CFD** with a transition-sensitive turbulence model — fully turbulent
models will misrepresent the bubble
* **Cited experimental data** at matching Re — NTRS [REF-NASA-003] and the
university low-Re airfoil databases
Whichever is used, name it in the output alongside the numbers it produced.
Related skills
| Skill | Stars | Updated | Works with | Status | Install |
|---|---|---|---|---|---|
| slack-gif-creatoranthropics/skillsKnowledge and utilities for creating animated GIFs optimized for Slack. Provides constraints, validation tools, and animation concepts. Use when users request animated GIFs for Slack like "make me a GIF of X doing Y for Slack." | Stars: 198k | Updated | Claude CodeCodex | Verified | Install |
| ponytailDietrichGebert/ponytailLazy senior dev mode for any coding task: the smallest change that fully solves it, and a reply a busy human understands in one read. | Stars: 194k | Updated | Claude CodeCodex | Verified | Install |
| ponytail-debtDietrichGebert/ponytailHarvest every shortcut: comment into one debt ledger, so deferrals get tracked instead of forgotten. One-shot report. | Stars: 194k | Updated | Claude CodeCodex | Verified | Install |
| ponytail-debtDietrichGebert/ponytailList every `shortcut:` comment (and older `ponytail:` ones) as a debt ledger. One-shot report, changes nothing. Use for "ponytail debt", "what did ponytail defer", "list the shortcuts", /ponytail-debt. | Stars: 194k | Updated | Claude CodeCodex | Verified | Install |