Skip to content

aden-hive/hive / core/framework/skills/_preset_skills/terminal-tools-troubleshooting

hive.terminal-tools-troubleshooting

Verified

Read when a terminal-tools call returned something surprising — empty stdout despite no error, exit_code is null, output_handle came back expired, "too many jobs" / "session busy" / "too many PTYs", warning was set unexpectedly, semantic_status disagrees with exit_code. Diagnostic recipes only — load on demand. Don't preload; the foundational skill covers the happy path.

Troubleshooting terminal-tools

Recipes for surprising results. Match the symptom to the section.

Empty stdout despite the command "should have" produced output

Possible causes:

  1. Output went to stderr instead. Check stderr in the envelope (or use merge_stderr=True for jobs).
  2. Output was fully truncated because max_output_kb is too small. Check stdout_truncated_bytes > 0. Bump max_output_kb or paginate via output_handle.
  3. Command produced no output (correct, just unexpected — silent flags, no matches).
  4. Pipeline issue: the last stage of a pipe ran but stdout went elsewhere (> /dev/null, redirected via 2>&1).
  5. Process is buffering its output and didn't flush before exit. Add stdbuf -oL (line-buffered) or unbuffer to the command.

exit_code: null

CauseOther field
Auto-backgroundedauto_backgrounded: true, job_id: <X>
Hard timeout, process killedtimed_out: true
Pre-spawn failure (command not found)error: ... set, pid: null
Still running (in terminal_job_logs)status: "running"

output_handle returned expired: true

5-minute TTL. Either (a) you waited too long, or (b) the store evicted it under memory pressure (64 MB total cap, LRU eviction). Re-run the command.

To reduce risk: paginate the handle as soon as you receive it, or use terminal_job_* for huge outputs (4 MB ring buffer with offsets — no expiry).

"too many jobs" / JobLimitExceeded

TERMINAL_TOOLS_MAX_JOBS (default 32) hit. Either:

  • Wait for jobs to exit (poll with terminal_job_logs(wait_until_exit=True))
  • Kill old jobs: terminal_job_manage(action="list") to see what's running, then signal_term the abandoned ones
  • Raise the cap via env (rare)

"session busy"

A terminal_pty_run was issued while another _run is in flight on the same session. PTY sessions are single-threaded conversations. Wait for the prior call to return, or open a second session.

"PTY cap reached"

TERMINAL_TOOLS_MAX_PTY (default 8) hit. Close idle sessions (terminal_pty_close). Idle reaping is lazy; force it by opening — no, actually, opening throws when the cap is hit. Just close manually.

warning is set, the command worked

Informational only. The pattern matched (e.g. rm -rf literally appears, or git push --force was used). The command ran. The warning is your "did I mean to do that?" prompt — verify the side effect was intended before continuing.

semantic_status: "ok" but exit_code: 1

Working as designed. Some commands use exit 1 for legitimate non-error states:

  • grep / rg exit 1 when no matches found
  • find exit 1 when some directories were unreadable (typical on /proc, etc.)
  • diff exit 1 when files differ
  • test / [ exit 1 when condition is false

The semantic_message field explains. Trust semantic_status, not raw exit_code.

semantic_status: "error" but exit_code: 0

Shouldn't happen. If it does, file a bug.

truncated_bytes_dropped > 0 in terminal_job_logs

Your since_offset was older than the ring buffer's floor — bytes evicted before you could read them. Either:

  • Poll faster (lower latency between calls)
  • Use merge_stderr=True (single 4 MB ring instead of 4 MB × 2)
  • Accept the gap and move forward from next_offset

terminal_pty_open succeeds but the first _run times out

The session may not have produced its first prompt sentinel within the 2-second startup window. Try:

  • A terminal_pty_run(sid, read_only=True, timeout_sec=2) to drain whatever's accumulated
  • A noop command (terminal_pty_run(sid, command="true")) to force a prompt cycle

Could also indicate the bash process died at startup — terminal_pty_run(sid, ...) would then return "session has exited".

shell="/bin/zsh" returned an error

By design. terminal-tools is bash-only on POSIX. Use shell=True (default /bin/bash) or omit shell= to exec directly.

A command in shell=True is interpreted differently than expected

Bash, not zsh, semantics. **/* doesn't recurse without shopt -s globstar; =cmd expansion doesn't work; arrays use arr[idx] not ${arr[idx]} differently than zsh. When in doubt, the foundational skill's "bash, not zsh" section is the canonical statement.

reverse-engineer-anythingmorluto/reaReverse engineer native, managed, Electron/JavaScript, packaged, firmware, and browser targets with REA, and build agent environments (AgentEnv bundles) of web applications from a live instance or a capture, and of Linux desktop apps with a task from a request. Use shipped-artifact or requested runtime evidence to explain features, compare versions, decompile code, or guide a reconstruction. Skip REA for ordinary source-repository architecture analysis.Stars: 471kUpdated Claude CodeCodexVerifiedInstall
diagnosing-superpowersobra/superpowersUse when a superpowers session went wrong and your human partner wants to know why — repeated work, ignored plans, stumbles, poor results, a skill that didn't fire, "it took too long", "why is it so expensive", "what is it doing" — or wants to build a bug report for the superpowers maintainers, for the current session or a past one identified by id or path, on any harness.Stars: 322kUpdated Claude CodeCodexVerifiedInstall
dispatching-parallel-agentsobra/superpowersUse when facing 2+ independent tasks that can be worked on without shared state or sequential dependenciesStars: 322kUpdated Claude CodeCodexVerifiedInstall
executing-plansobra/superpowersUse when executing an implementation plan in the current session as the implementer yourself — your human partner chose inline execution, or no subagent tool is availableStars: 322kUpdated Claude CodeCodexVerifiedInstall