Skip to content

matlab/matlab-agentic-toolkit / skills-catalog/test-and-measurement/matlab-use-vehicle-network

matlab-use-vehicle-network

Unverified

Use when setting up vehicle network communication in MATLAB using Vehicle Network Toolbox. Covers CAN/CAN FD (fully implemented), with architecture for J1939, XCP, and future protocols. Handles hardware discovery, channel creation, bus configuration, message exchange, signal encoding/decoding, and analysis across all supported vendors. (Vector, Kvaser, PEAK-System, NI, SocketCAN, MathWorks Virtual).

FileKindSize
SKILL.mdskill md13.1 KB
manifest.yamlconfig537 B
references/can/bus-speed-config.mdmarkdown2.2 KB
references/can/channel-creation.mdmarkdown1.5 KB
references/can/database.mdmarkdown3.0 KB
references/can/filters.mdmarkdown2.8 KB
references/can/message-creation.mdmarkdown1.3 KB
references/can/message-extraction.mdmarkdown3.8 KB
references/can/pack-unpack.mdmarkdown2.6 KB
references/can/receive.mdmarkdown1.9 KB
references/can/transmit.mdmarkdown2.3 KB
references/can/troubleshooting/bus-length-guidelines.mdmarkdown3.5 KB
references/can/troubleshooting/diagnostic-workflow.mdmarkdown21.4 KB
references/can/troubleshooting/l1-branches.mdmarkdown11.1 KB
references/can/troubleshooting/l1-domain-knowledge.mdmarkdown6.8 KB
references/can/troubleshooting/l1-failure-scenarios.mdmarkdown3.6 KB
references/can/troubleshooting/l2-analysis-pipeline.mdmarkdown4.5 KB
references/can/troubleshooting/l2-interpretation-tables.mdmarkdown1.8 KB
references/can/troubleshooting/script-interfaces.mdmarkdown2.6 KB
references/shared/channel-lifecycle.mdmarkdown1.1 KB
references/shared/hardware-discovery.mdmarkdown1.1 KB
references/shared/limitations.mdmarkdown1.7 KB
scripts/can/troubleshooting/canBaudRateScanActive.pbinary1.0 KB
scripts/can/troubleshooting/canBaudRateScanPassive.pbinary1.0 KB
scripts/can/troubleshooting/canBurstDetection.pbinary488 B
scripts/can/troubleshooting/canBusLoadCalc.pbinary787 B
scripts/can/troubleshooting/canChannelHealthCheck.pbinary902 B
scripts/can/troubleshooting/canCycleTimeAnalysis.pbinary558 B
scripts/can/troubleshooting/canDiagnosticProbe.pbinary335 B
scripts/can/troubleshooting/canHardwareDiscovery.pbinary290 B
scripts/can/troubleshooting/canLoopbackSelfTest.pbinary628 B
scripts/can/troubleshooting/canSupportSummary.pbinary1.4 KB
scripts/can/troubleshooting/canTrafficOverview.pbinary900 B

references/can/troubleshooting/l1-failure-scenarios.md

View on GitHub
# L1 Failure Scenarios

Pattern-matching table for rapid diagnosis. Use when Phase 1 routing is ambiguous or to confirm a suspected root cause.

---

## Symptom -> Domain Mapping

| Observed Symptom | Primary Domain | Secondary | Key Question |
|-----------------|---------------|-----------|--------------|
| 40-ohm termination (measured) | Termination | — | "Did you add a tool recently?" (built-in 120-ohm) |
| Works on bench, fails in vehicle | Ground | Waveform | "How are grounds connected?" (chassis ground shift) |
| Errors when motor/VFD/heater starts | Ground | — | "Measure ground potential between nodes under load" |
| One node can't join, all others fine | Bit Timing | Termination | "Does that node use the same baud rate?" |
| Added analyzer, now failing | Termination | — | "Does analyzer have built-in termination? (DIP switch)" |
| Intermittent CRC, temperature-correlated | Waveform | Bit Timing | "Crystal or ceramic resonator?" (thermal drift) |
| TEC climbs on one node only | Voltage | Waveform | "Check that node's TX path: transceiver, stub, connector" |
| REC climbs on ALL nodes | Termination | Ground | "Shared physical issue — backbone termination or ground" |
| BusOff immediately on start | Bit Timing | Termination | "Verify baud matches network; check for open bus" |
| Errors only at high bus load | Bit Timing | Ground | "Sample point mismatch visible under arbitration stress" |
| Works at 250k, fails at 500k | Waveform | Termination | "Stubs too long for higher rate; check cable quality" |
| Errors after moving system | Ground | Waveform | "New ground path; check cable integrity" |
| Garbage frames (high count, corrupted) | Bit Timing | — | "Baud mismatch — receiver decoding noise as frames" |
| FD errors only | CAN FD | — | "Does the nodes on the network support CAN FD or just classic CAN?" |
| FD data-phase errors only | CAN FD | — | "Stubs eliminated? Bus length within data-phase limits? Sample point configured?" |
| Errors correlate with specific message IDs | Bit Timing | — | "Not physical — data-dependent stuff patterns" |

---

## Scenario Playbooks

### New Setup: Complete Silence
**Check order:** Termination -> Bit Timing -> Voltage
1. Measure 60 ohms between H and L (power off)
2. Confirm all nodes configured to same baud
3. Verify CAN_H and CAN_L idle at ~2.5V

### Was Working: Sudden Complete Failure
**Check order:** Termination -> Bit Timing -> Voltage
1. "What changed?" — any new device, cable, or firmware update
2. If device added: check for extra termination
3. If firmware updated: verify baud rate wasn't altered
4. If nothing changed: check for broken wire or connector (resistance test)

### Intermittent: Correlates with Environment
**Check order:** Ground -> Waveform -> Bit Timing
1. Identify correlation (load activation, temperature, time of day)
2. Measure ground potential under worst-case conditions
3. If ground clean: oscilloscope waveform during fault event
4. If waveform clean: check SJW vs oscillator quality

### Rising Error Counters: Gradual Degradation
**Check order:** Varies by pattern (see Error Counter Interpretation in SKILL.md)
- TEC on one node -> that node's TX path
- REC on one node -> that node's RX (ground at that node)
- REC on all -> shared backbone issue
- Both climbing -> severe local fault

### CAN FD Specific
**Check order:** CAN FD -> Bit Timing -> Waveform
1. Stubs eliminated for data-phase rate? (See bus-length-guidelines.md)
2. Bus length within data-phase limits?
3. Any classical nodes on the same segment?
4. Data-phase sample point configured correctly?

----

Copyright 2026 The MathWorks, Inc.

----
slack-gif-creatoranthropics/skillsKnowledge and utilities for creating animated GIFs optimized for Slack. Provides constraints, validation tools, and animation concepts. Use when users request animated GIFs for Slack like "make me a GIF of X doing Y for Slack."Stars: 198kUpdated Claude CodeCodexVerifiedInstall
ponytailDietrichGebert/ponytailLazy senior dev mode for any coding task: the smallest change that fully solves it, and a reply a busy human understands in one read.Stars: 194kUpdated Claude CodeCodexVerifiedInstall
ponytail-debtDietrichGebert/ponytailHarvest every shortcut: comment into one debt ledger, so deferrals get tracked instead of forgotten. One-shot report.Stars: 194kUpdated Claude CodeCodexVerifiedInstall
ponytail-debtDietrichGebert/ponytailList every `shortcut:` comment (and older `ponytail:` ones) as a debt ledger. One-shot report, changes nothing. Use for "ponytail debt", "what did ponytail defer", "list the shortcuts", /ponytail-debt.Stars: 194kUpdated Claude CodeCodexVerifiedInstall