Skip to content

matlab/matlab-agentic-toolkit / skills-catalog/test-and-measurement/matlab-use-vehicle-network

matlab-use-vehicle-network

Unverified

Use when setting up vehicle network communication in MATLAB using Vehicle Network Toolbox. Covers CAN/CAN FD (fully implemented), with architecture for J1939, XCP, and future protocols. Handles hardware discovery, channel creation, bus configuration, message exchange, signal encoding/decoding, and analysis across all supported vendors. (Vector, Kvaser, PEAK-System, NI, SocketCAN, MathWorks Virtual).

FileKindSize
SKILL.mdskill md13.1 KB
manifest.yamlconfig537 B
references/can/bus-speed-config.mdmarkdown2.2 KB
references/can/channel-creation.mdmarkdown1.5 KB
references/can/database.mdmarkdown3.0 KB
references/can/filters.mdmarkdown2.8 KB
references/can/message-creation.mdmarkdown1.3 KB
references/can/message-extraction.mdmarkdown3.8 KB
references/can/pack-unpack.mdmarkdown2.6 KB
references/can/receive.mdmarkdown1.9 KB
references/can/transmit.mdmarkdown2.3 KB
references/can/troubleshooting/bus-length-guidelines.mdmarkdown3.5 KB
references/can/troubleshooting/diagnostic-workflow.mdmarkdown21.4 KB
references/can/troubleshooting/l1-branches.mdmarkdown11.1 KB
references/can/troubleshooting/l1-domain-knowledge.mdmarkdown6.8 KB
references/can/troubleshooting/l1-failure-scenarios.mdmarkdown3.6 KB
references/can/troubleshooting/l2-analysis-pipeline.mdmarkdown4.5 KB
references/can/troubleshooting/l2-interpretation-tables.mdmarkdown1.8 KB
references/can/troubleshooting/script-interfaces.mdmarkdown2.6 KB
references/shared/channel-lifecycle.mdmarkdown1.1 KB
references/shared/hardware-discovery.mdmarkdown1.1 KB
references/shared/limitations.mdmarkdown1.7 KB
scripts/can/troubleshooting/canBaudRateScanActive.pbinary1.0 KB
scripts/can/troubleshooting/canBaudRateScanPassive.pbinary1.0 KB
scripts/can/troubleshooting/canBurstDetection.pbinary488 B
scripts/can/troubleshooting/canBusLoadCalc.pbinary787 B
scripts/can/troubleshooting/canChannelHealthCheck.pbinary902 B
scripts/can/troubleshooting/canCycleTimeAnalysis.pbinary558 B
scripts/can/troubleshooting/canDiagnosticProbe.pbinary335 B
scripts/can/troubleshooting/canHardwareDiscovery.pbinary290 B
scripts/can/troubleshooting/canLoopbackSelfTest.pbinary628 B
scripts/can/troubleshooting/canSupportSummary.pbinary1.4 KB
scripts/can/troubleshooting/canTrafficOverview.pbinary900 B

references/can/transmit.md

View on GitHub
# Transmit

## transmit — One-shot send

```matlab
transmit(ch, msg);
```

- Non-blocking — returns immediately
- Ignores `Timestamp` and `Error` properties on the message
- **CAN is peer-to-peer:** at least one other node must be present on the physical bus to acknowledge. Without another node, transmission fails as an error frame and the device retries continuously.

## transmitPeriodic — Fixed interval

```matlab
transmitPeriodic(ch, msg, 'On', period);   % enable (period in seconds, default 0.5)
transmitPeriodic(ch, msg, 'Off');           % disable
```

- Can enable/disable **while channel is running**
- Changing `msg.Data` (e.g., via `pack`) updates what gets sent on next cycle
- Period is in seconds (numeric)

## transmitEvent — Send on data write

```matlab
transmitEvent(ch, msg, 'On');
transmitEvent(ch, msg, 'Off');
```

- Triggers transmission on any `.Data` property **assignment** — even if the value is identical
- `pack(msg, ...)` triggers event transmit because it writes to `.Data` internally
- Typically used with `pack(msg, value, startBit, length, byteOrder)` for signal-level updates
- Multiple messages can be event-enabled on the same channel independently

## Combining Periodic + Event

Different messages on the same channel can have independent transmit modes:

```matlab
statusMsg = canMessage(0x180, false, 8);   % telemetry
alarmMsg = canMessage(0x700, false, 8);    % fault notification

transmitPeriodic(ch, statusMsg, 'On', 0.1);  % 100ms cycle
transmitEvent(ch, alarmMsg, 'On');           % only on fault

start(ch);

% Update periodic data live — next cycle uses new value
pack(statusMsg, int16(3000), 0, 16, 'LittleEndian');

% Trigger alarm only when needed
alarmMsg.Data = uint8([0x01 92 0 0 0 0 0 0]);
```

**Typical pattern:** Periodic for status/telemetry, event-based for alarms/faults.

## replay — Retransmit with original timing

```matlab
replay(ch, msgs);
```

- Retransmits messages based on relative differences of their timestamps
- Input: timetable of messages, message object, or array of message objects
- Also works from MATLAB to Simulink

## transmitConfiguration — View current setup

```matlab
transmitConfiguration(ch);
```

- Displays all periodic and event-based messages configured on the channel
- Shows: ID, Extended flag, Name, Data, Rate (for periodic)

----

Copyright 2026 The MathWorks, Inc.

----
slack-gif-creatoranthropics/skillsKnowledge and utilities for creating animated GIFs optimized for Slack. Provides constraints, validation tools, and animation concepts. Use when users request animated GIFs for Slack like "make me a GIF of X doing Y for Slack."Stars: 198kUpdated Claude CodeCodexVerifiedInstall
ponytailDietrichGebert/ponytailLazy senior dev mode for any coding task: the smallest change that fully solves it, and a reply a busy human understands in one read.Stars: 194kUpdated Claude CodeCodexVerifiedInstall
ponytail-debtDietrichGebert/ponytailHarvest every shortcut: comment into one debt ledger, so deferrals get tracked instead of forgotten. One-shot report.Stars: 194kUpdated Claude CodeCodexVerifiedInstall
ponytail-debtDietrichGebert/ponytailList every `shortcut:` comment (and older `ponytail:` ones) as a debt ledger. One-shot report, changes nothing. Use for "ponytail debt", "what did ponytail defer", "list the shortcuts", /ponytail-debt.Stars: 194kUpdated Claude CodeCodexVerifiedInstall