Griffing-Technology-LLC/engineering-pe-skills / skills/naval-architecture-marine
naval-architecture-marine
VerifiedNaval architecture and marine engineering — ship hydrostatics, intact stability (GZ curve, metacentric height, IMO weather criterion), trim and freeboard, hull resistance and powering, and propeller/propulsion coefficients. Use when computing displacement or buoyancy, finding the metacentric height or righting arm, checking IMO intact stability criteria, analysing trim or list, estimating hull resistance from Froude or Reynolds number, applying the ITTC-57 friction line, or sizing propulsion power for a vessel.
| File | Kind | Size |
|---|---|---|
| SKILL.md | skill md | 8.1 KB |
| references/hydrostatics-and-stability.md | markdown | 5.0 KB |
| references/resistance-and-propulsion.md | markdown | 5.5 KB |
references/resistance-and-propulsion.md
View on GitHub# Resistance and Propulsion
Reference file for the `naval-architecture-marine` skill. The resistance
decomposition, ITTC-57 friction line, and Froude/Reynolds definitions in §1–2
are read verbatim from ITTC Recommended Procedure 7.5-02-02-01
[REF-ITTC-001]. Propulsion-coefficient framework in §3 is standard
naval-architecture practice [REF-SNAME-001] — no specific PNA page is cited;
see the caution against REF-SNAME-001 in `REFERENCES.md`.
**Scope note (from the source procedure itself):** this method set addresses
**conventional displacement vessels** only. Vessels with $Fr > 0.45$, or speeds
above $3.7\,\nabla^{1/6}$ (m/s), or planing/dynamically-supported craft, are
addressed by a different ITTC procedure (7.5-02-05-01, High Speed Marine
Vehicle Resistance Test) not catalogued in this repository — flag that gap
explicitly rather than applying this method outside its stated range.
## 1. Why two scaling laws, not one
A ship's total resistance has a viscous (frictional) component and a
wave-making component. Viscous drag scales with **Reynolds number**
$Re = VL/\nu$; wave pattern scales with **Froude number** $Fr = V/\sqrt{gL}$.
A geometrically-scaled model run at the ship's $Fr$ (correct wave pattern) runs
at a much lower $Re$ than the full-scale ship, so its *relative* frictional
resistance is too high. There is no model speed that matches both numbers at
once for a practical scale ratio — that mismatch is exactly why resistance is
extrapolated by **component**, not by a single overall coefficient.
$$Fr = \frac{V}{\sqrt{gL}}, \qquad Re = \frac{VL}{\nu}$$
$Fr_h = V/\sqrt{gh}$ is the depth Froude number, for shallow or restricted
water.
## 2. Resistance-coefficient decomposition
Non-dimensionalise on $\tfrac{1}{2}\rho S V^2$ ($S$ = wetted surface area):
$$C_T = \frac{R_T}{\tfrac{1}{2}\rho S V^2}$$
$$C_V = C_F(1+k), \qquad C_W = C_T - C_V = C_T - C_F(1+k)$$
$C_T$ — total resistance coefficient (measured, model test); $C_V$ — viscous
resistance coefficient; $C_W$ — wave-making resistance coefficient (assumed
to obey Froude similarity, and therefore transferable from model to ship at
matched $Fr$); $(1+k)$ — form factor, accounting for 3-D viscous effects a flat
plate does not have.
**1957 ITTC model-ship correlation line** — the frictional resistance
coefficient of an equivalent flat plate at the given Reynolds number:
$$C_F = \frac{0.075}{(\log_{10}Re - 2)^2} = (1 + 0.1194)\,\frac{0.067}{(\log_{10}Re-2)^2}$$
Extrapolation procedure, in outline:
1. Measure $C_{T,model}$ from a towing-tank test at the model's $Fr$-matched
speed; determine $Re_{model}$ for that run.
2. Compute $C_{F,model}$ from the ITTC-57 line at $Re_{model}$; obtain the form
factor $k$ (from a low-speed run or an empirical method) and $C_{V,model}$.
3. $C_{W,model} = C_{T,model} - C_{V,model}$. **Assume $C_W$ is scale-independent
at matched $Fr$** — this is the Froude-similarity assumption at the core of
the whole method.
4. Compute $C_{F,ship}$ from the ITTC-57 line at the ship's (much larger)
$Re_{ship}$, at the same $Fr$-matched speed scaled to full size.
5. $C_{T,ship} = C_{F,ship}(1+k) + C_{W,model} + C_A$, where $C_A$ is a
correlation allowance accounting for hull roughness and residual scale
effects not captured by the form-factor method.
6. Add appendage resistance $C_{APP}$ and air/wind resistance $C_{AA}$ as
needed for the actual ship condition.
## 3. Effective and delivered power
$$P_E = R_T \, V$$
$P_E$ — effective (towrope) power: the power to tow the bare hull at speed $V$
with no propulsion losses. This is **not** the power the engine must deliver.
**Propulsion factors** connect $P_E$ to shaft power:
$$\eta_H = \frac{1-t}{1-w}, \qquad \eta_D = \eta_H\,\eta_0\,\eta_R$$
* $w$ — wake fraction: the propeller works in water already moving with the
hull's boundary layer and wave system, so its inflow speed is less than
ship speed.
* $t$ — thrust deduction: the propeller's suction accelerates flow past the
stern, adding resistance beyond the bare-hull figure.
* $\eta_H$ — hull efficiency, from $w$ and $t$ together — commonly $> 1$ for
single-screw hulls, which is a real hydrodynamic interaction effect, not an
error.
* $\eta_0$ — open-water propeller efficiency, from the propeller's own
characteristic curves at its operating advance coefficient $J$.
* $\eta_R$ — relative rotative efficiency, correcting open-water efficiency for
the actual (non-uniform) wake field behind the hull.
* $\eta_D$ — quasi-propulsive coefficient, the product of all three.
$$P_D = \frac{P_E}{\eta_D}$$
$P_D$ — delivered power at the propeller. Shaft power adds shafting losses;
brake (engine) power adds gearbox losses on top of that. **State which power
definition is being reported** — $P_E$, $P_D$, shaft, or brake — they are not
interchangeable and differ by tens of percent.
## 4. Sea and service margins
Trial-condition resistance is not service resistance. State explicitly what
margin was added for hull fouling, weather, and shallow-water effects, and
where that margin figure came from (a specific standard, class-society
guidance, or an engineering judgement being declared) — an unstated margin is
not a margin, it is a guess wearing a number.
## 5. Out of scope here
Cavitation inception, propeller strength/blade design, detailed self-propulsion
model-test correction methods beyond the outline in §2, and high-speed/planing
hull resistance (a different ITTC procedure, not catalogued here) are **not
covered**. Name them explicitly as out of scope when a request reaches into
them.
Related skills
| Skill | Stars | Updated | Works with | Status | Install |
|---|---|---|---|---|---|
| slack-gif-creatoranthropics/skillsKnowledge and utilities for creating animated GIFs optimized for Slack. Provides constraints, validation tools, and animation concepts. Use when users request animated GIFs for Slack like "make me a GIF of X doing Y for Slack." | Stars: 198k | Updated | Claude CodeCodex | Verified | Install |
| ponytailDietrichGebert/ponytailLazy senior dev mode for any coding task: the smallest change that fully solves it, and a reply a busy human understands in one read. | Stars: 194k | Updated | Claude CodeCodex | Verified | Install |
| ponytail-debtDietrichGebert/ponytailHarvest every shortcut: comment into one debt ledger, so deferrals get tracked instead of forgotten. One-shot report. | Stars: 194k | Updated | Claude CodeCodex | Verified | Install |
| ponytail-debtDietrichGebert/ponytailList every `shortcut:` comment (and older `ponytail:` ones) as a debt ledger. One-shot report, changes nothing. Use for "ponytail debt", "what did ponytail defer", "list the shortcuts", /ponytail-debt. | Stars: 194k | Updated | Claude CodeCodex | Verified | Install |