Griffing-Technology-LLC/engineering-pe-skills / skills/naval-architecture-marine
naval-architecture-marine
VerifiedNaval architecture and marine engineering — ship hydrostatics, intact stability (GZ curve, metacentric height, IMO weather criterion), trim and freeboard, hull resistance and powering, and propeller/propulsion coefficients. Use when computing displacement or buoyancy, finding the metacentric height or righting arm, checking IMO intact stability criteria, analysing trim or list, estimating hull resistance from Froude or Reynolds number, applying the ITTC-57 friction line, or sizing propulsion power for a vessel.
| File | Kind | Size |
|---|---|---|
| SKILL.md | skill md | 8.1 KB |
| references/hydrostatics-and-stability.md | markdown | 5.0 KB |
| references/resistance-and-propulsion.md | markdown | 5.5 KB |
references/hydrostatics-and-stability.md
View on GitHub# Hydrostatics and Intact Stability
Reference file for the `naval-architecture-marine` skill. Numeric criteria in
§3 are read verbatim from the IMO 2008 IS Code, 2020 Edition [REF-IMO-001].
Method framework (KB, BM, GZ) is standard naval-architecture practice
[REF-SNAME-001]; no specific PNA page is cited — see the caution against
REF-SNAME-001 in `REFERENCES.md`.
## 1. Buoyancy and displacement
Archimedes' principle: a floating body displaces a weight of fluid equal to its
own weight.
$$\Delta = \rho \, \nabla$$
$\Delta$ — displacement (mass, `t` or `lbm`); $\rho$ — water density
(salt water $\approx 1.025\ \mathrm{t/m^3}$, fresh $\approx 1.000\ \mathrm{t/m^3}$
— **the difference is not negligible for draft and stability**); $\nabla$ —
underwater volume.
**Tonnes per centimetre immersion (TPC):**
$$TPC = \frac{A_{wp}\,\rho}{100}$$
$A_{wp}$ — waterplane area. Use TPC for small draft-change estimates only; it
assumes a near-vertical, near-constant waterplane over the change.
**Fresh water allowance (FWA)** corrects the load-line draft for the density
change between salt and fresh water — apply it, do not assume salt-water
density universally.
## 2. Metacentric height and the righting arm
$KB$ is read from the hull form or hydrostatic curves.
$$BM = \frac{I_T}{\nabla}$$
$I_T$ — transverse second moment of the waterplane area about the centreline.
Then:
$$KM = KB + BM, \qquad GM = KM - KG$$
$GM$ — metacentric height, the small-angle stability lever arm about the
initial upright condition. **Valid only for small heel angles** (roughly
$< 10°$–$15°$) where $BM$ is effectively constant; beyond that, use the actual
GZ (cross) curves, not $GM\sin\varphi$.
**Righting arm (GZ):**
$$GZ = KN - KG\sin\varphi \quad \text{(from cross curves of stability, "KN curves")}$$
or, at small angles only:
$$GZ \approx GM \sin\varphi$$
**Free surface correction — never skip this.** A slack (partially full) tank
generates a free-surface moment $FSM$ that reduces the *effective* GM:
$$GM_{eff} = GM - \frac{FSM}{\Delta}$$
$FSM$ sums over every slack tank; a single large slack tank can eliminate most
of a vessel's stability margin. This applies "in all conditions of loading"
per the Code itself [REF-IMO-001 §2.1.2].
## 3. IMO 2008 IS Code, Part A — general intact stability criteria
Read verbatim from the 2020 Edition [REF-IMO-001], applicable to cargo and
passenger ships $\geq 24$ m in length (§1.1.1):
| § | Criterion |
| --- | --- |
| 2.2.1 | Area under GZ curve $\geq 0.055$ m·rad up to $\varphi = 30°$ |
| 2.2.1 | Area under GZ curve $\geq 0.090$ m·rad up to $\varphi = 40°$ (or $\varphi_f$ if less) |
| 2.2.1 | Area between $30°$ and $40°$ (or $30°$–$\varphi_f$) $\geq 0.030$ m·rad |
| 2.2.2 | $GZ \geq 0.20$ m at an angle of heel $\geq 30°$ |
| 2.2.3 | Max GZ occurs at heel $\geq 25°$ (or approved equivalent) |
| 2.2.4 | Initial metacentric height $GM_0 \geq 0.15$ m |
All criteria in this table apply **simultaneously** — none supersedes another.
### Severe wind and rolling ("weather") criterion — §2.3
Independent of the table above; evaluate it separately.
1. Steady wind heeling lever:
$$l_{w1} = \frac{P\,A\,Z}{1000\,g\,\Delta}\ \text{(m)}, \qquad P = 504\ \mathrm{Pa}$$
$A$ — projected lateral windage area above the waterline (m²); $Z$ —
vertical distance from the centre of $A$ to the centre of underwater
lateral area, or approximately half draft (m); $g = 9.81\ \mathrm{m/s^2}$.
2. Steady heel angle $\varphi_0$ from $l_{w1}$ against the GZ curve; must not
exceed $16°$ or 80% of the deck-edge immersion angle, whichever is less.
3. Gust heeling lever: $l_{w2} = 1.5\,l_{w1}$.
4. Windward roll angle $\varphi_1$ (from Code Part B / an approved method), then
**area $b \geq$ area $a$** per the Code's Figure 2.3.1-1, evaluated between
$\varphi_0$ and $\varphi_2$ ($\varphi_2$ = down-flooding angle, $50°$, or the
second GZ/wind-lever intercept $\varphi_c$ — whichever is least).
5. An alternative test method may substitute a measured wind speed of
26 m/s full-scale, subject to Administration approval [REF-IMO-001 §2.3.3].
**This skill states the criteria; it does not perform the roll-angle
prediction of §2.3.1.2**, which draws on Part B methods not yet catalogued in
this repository. Flag that gap explicitly if a weather-criterion check is
requested in full.
## 4. Trim
Trim is the difference between forward and aft drafts. For a small trimming
moment about the centre of flotation (LCF):
$$t = \frac{Trimming\ Moment}{MCT1cm}$$
$MCT1cm$ — moment to change trim 1 cm, a hydrostatic-curve property. Report
trim by the bow or by the stern explicitly — the sign convention is a common
source of error.
## 5. Out of scope here
Longitudinal hull-girder strength, scantlings, classification-society
structural rules, damage stability (a separate IMO framework from intact
stability), and load-line freeboard tables are **not covered** by this
reference file. Name them explicitly as out of scope when a request reaches
into them.
Related skills
| Skill | Stars | Updated | Works with | Status | Install |
|---|---|---|---|---|---|
| slack-gif-creatoranthropics/skillsKnowledge and utilities for creating animated GIFs optimized for Slack. Provides constraints, validation tools, and animation concepts. Use when users request animated GIFs for Slack like "make me a GIF of X doing Y for Slack." | Stars: 198k | Updated | Claude CodeCodex | Verified | Install |
| ponytailDietrichGebert/ponytailLazy senior dev mode for any coding task: the smallest change that fully solves it, and a reply a busy human understands in one read. | Stars: 194k | Updated | Claude CodeCodex | Verified | Install |
| ponytail-debtDietrichGebert/ponytailHarvest every shortcut: comment into one debt ledger, so deferrals get tracked instead of forgotten. One-shot report. | Stars: 194k | Updated | Claude CodeCodex | Verified | Install |
| ponytail-debtDietrichGebert/ponytailList every `shortcut:` comment (and older `ponytail:` ones) as a debt ledger. One-shot report, changes nothing. Use for "ponytail debt", "what did ponytail defer", "list the shortcuts", /ponytail-debt. | Stars: 194k | Updated | Claude CodeCodex | Verified | Install |