Skip to content

Echo-aloha/asphalt-codex-skills-5 / skills/pfc-marshall-test

pfc-marshall-test

Verified

Adapt and audit a PFC 5.0 asphalt Marshall stability/flow simulation using the external fistPkg26 dc.fis two-head controller as a starting skeleton; use for curved-head geometry, PFC5 wall/contact kinematics, load-deformation histories, peak stability, edition-specific flow processing, and validation against laboratory data.

references/overview.md

View on GitHub
# 马歇尔试验的底层框架:fistPkg dc.fis

> 本文件提炼自 Itasca fistPkg26 `dc.fis`(PFC 5.0)。马歇尔可以复用其
> 双头控制骨架,但不是巴西劈裂强度试验。弧形几何之外仍需验证墙 ID/轴向、
> 接触、平滑、力/位移、终止和规范后处理。

## 1. 框架定位

`dc.fis` 提供**劈裂(间接拉伸)试验**的支持函数:两个相对压板
(platen/head)沿直径方向压缩圆柱试件,监测 wall-based 轴向力与应变。
马歇尔可复用相对运动和反力采集骨架,但压头几何、试件形成/调温、装置约束、
采样、曲线修正、稳定度/流值和水敏感性分支均不同,不能概括为“只换压头”。

## 2. 官方参数(在 dcParams.p2dat/p3dat 的 `dcSetParams` 中设置)

| 参数 | 含义 | 默认/说明 |
| --- | --- | --- |
| dc_w | 压板宽 | 必填,> 0 |
| dc_d | 压板深(仅 3D) | 3D 必填,2D 为单位厚度 |
| dc_emod | 压板有效模量(linear 接触用) | 缺省回退 mv_emod |
| dc_g0 | 初始压板间距 | 必填,> 0 |
| dc_eRate | 轴向应变率 | 必填,> 0;墙速 = 0.5·dc_eRate·dc_g0 |
| dc_loadCode | 加载阶段代码 | 0 单阶段 / 1 多阶段 |
| dc_loadFac | 荷载终止因子 | 默认 0.9(\|dc_wfa\| ≤ dc_loadFac·峰值 时停) |
| dc_ARatLimit | 平衡比限(ft_eq 参数) | 默认 1.0e-5 |
| dc_stepLimit | 步数限(ft_eq 参数) | 默认 200 万 |

内部量(只读):

| 量 | 含义 |
| --- | --- |
| dcWp0 / dcWp1 | 下 / 上压板指针 |
| dc_wfa | wall-based 轴向力(正为拉伸) |
| dc_wea | wall-based 轴向应变(正为张开) |
| dc_wda | wall-based 轴向位移(= dc_wea·dc_g0) |
| dc_wfaMax | 轴向力绝对值最大值 |

## 3. 官方流程

```
dcSetupPhase    创建墙 → 去重叠 → 应变清零 → 静力平衡 → 存 <matName>-dc0
dcLoadingPhase  施加轴向应变 → 记录力/应变 → 荷载终止准则 → 存 <matName>-dc1
```

- `dcSetupPhase`:调 `_dcMakeWalls` 建墙 → `clean` 去颗粒-墙重叠 → `ft_SmoothGrainWallInterface` → `dc_wInit`(挂 callback:42.1 力、10.10 应变)→ `ft_eq` 静力平衡 → 存 dc0。
- `dcLoadingPhase`:单阶段(dc_loadCode=0)走 `_dcPerformStage(1, -1.0)`;多阶段走用户提供的 `dcPerformStages`。
- `_dcApplyAxialStrain`:设墙速 `0.5·dc_eRate·dc_g0`,`solve fishhalt _aASTPPdone`,终止准则为 `|dc_wfa| ≤ dc_loadFac·dc_wfaMax`。

## 4. 扩展点 `_dcMakeWalls`

官方 `_dcMakeWalls` 用**平面压板**:

```fish
def _dcMakeWalls
    ft_setGrainWallBehavior('existing', 0.0, dc_emod, 0.0, 0.0, 'linear')
    ft_setGrainWallBehavior('future',   0.0, dc_emod, 0.0, 0.0, 'linear')
    ; 3D:wall generate ... polygon ... makeplanar(宽 dc_w × 深 dc_d 的平面压板)
    ; 2D:wall create ... vertices(线段压板)
    dcWp0 = wall.find(1)   ; 下压板
    dcWp1 = wall.find(2)   ; 上压板
end
```

重定义 `_dcMakeWalls` 是更换弧形压头的最小钩子,不是完整适配的充分
条件。其余 `dc.fis` 逻辑必须按目标 PFC5 版本和标准版次逐项审计后才能复用。

> JTG E20-2011 已被 JTG 3410-2025 替代。现行马歇尔方法已核对为
> T 0709-2025,并需追溯 T 0702-2025 成型。旧 T0709 只用于明确的历史复现。

## 5. 稳定度与流值(规范概念)

- **稳定度 MS**:试件加载过程中出现的峰值荷载(kN)。
- **流值 FL**:对应峰值荷载时的变形(mm)。
- **马歇尔模数 T** = MS / FL。

DEM 输出的是 wall-based 轴向力 `dc_wfa` 与 wall-based 轴向位移 `dc_wda`。
它们只是原始曲线候选量;规范结果必须先统一两压头反力/相对位移、符号和单位,
再按 T 0709-2025 做原点修正,并对峰值不明显的曲线采用当前方法的独立分支。
详见 `jtg-3410-2025-t0709.md`。

PFC5 官方 `wall.force.contact` 返回**作用在该 wall 上的所有接触力之和**,并以
全局坐标表示;第二参数/`.x/.y/.z` 只是在全局坐标中取分量。相对布置的两个
压头应分别记录反力,在声明的加载轴上检查等值反向与不平衡误差,再按一个明确
的单压头、平均幅值或其他装置约定生成标量荷载。不能直接把带符号两反力相加。

`wall.disp` 是可读写的累计 wall displacement。建立预载参考时应同时保存两墙
位置/位移与初始间距,避免恢复存档或手动清零后把不同参考系的量混在一条曲线。

## 6. 监测与裂纹

- 力/应变由 `dc.fis` 的 callback(42.1 / 10.10)自动记录。
- 若试件为胶结材料(PB),配合 `ck.fis`/`ms` 裂纹监测,记录拉伸/剪切裂纹数。
rea-analysis-optimizationmorluto/reaOptimize REA providers and shared analysis workflows for agent context, latency, CPU, and memory while preserving correctness and Evidence. Use for analysis bottlenecks and cache or query design; CI/test-suite optimization belongs to rea-ci-tests-audit.Stars: 472kUpdated Claude CodeCodexVerifiedInstall
rea-ci-tests-auditmorluto/reaAudit REA CI and test suites for correctness, fixture drift, false passes, and measured performance; use for suite or workflow investigations and efficiency changes, rather than ordinary feature testing or a single test failure.Stars: 472kUpdated Claude CodeCodexVerifiedInstall
rea-tool-designmorluto/reaAudit, investigate, design, or change REA investigation tools, CLI/MCP contracts, provider capabilities, and Evidence semantics.Stars: 472kUpdated Claude CodeCodexVerifiedInstall
ponytail-auditDietrichGebert/ponytailQuality audit of the whole repo: bugs, security, real load, missing tests, speed, and what to delete. Most important first.Stars: 194kUpdated Claude CodeCodexVerifiedInstall