Skip to content

Echo-aloha/asphalt-codex-skills-5 / skills/pfc-marshall-test

pfc-marshall-test

Verified

Adapt and audit a PFC 5.0 asphalt Marshall stability/flow simulation using the external fistPkg26 dc.fis two-head controller as a starting skeleton; use for curved-head geometry, PFC5 wall/contact kinematics, load-deformation histories, peak stability, edition-specific flow processing, and validation against laboratory data.

references/jtg-3410-2025-t0709.md

View on GitHub
# JTG 3410-2025 T 0709 马歇尔方法契约

本文件是面向模型的核对清单,不替代规范原文。方法编号、处理逻辑和报告字段已
按 JTG 3410-2025 的 T 0709-2025(印刷页 372-377)核对;压头尺寸表、完整
仪器指标、允许误差和项目验收限值仍从合法规范副本读取。

## 来源绑定

- ledger: `../../pfc5-asphalt-workflow/references/standards-source-ledger.json`
- source_id: `user-supplied-licensed-copy:jtg-3410-2025`
- source_sha256: `1B57C826AE26397C85C76497BF4724D7E53DD20BFC4C3F6E988F2E85A3B33A6F`
- method_id: `T 0709-2025`
- printed_pages_reviewed: `372-377`

该绑定证明本清单对应哪一份已审阅副本;正式工程使用仍需人工确认适用性及
项目采用版本。

## 适用性和前置链

- 当前方法编号为 `T 0709-2025`,适用于标准和大型马歇尔试件;试件成型来源
  是 T 0702-2025。
- 标准稳定度/流值、浸水稳定度比和真空饱水稳定度比是不同试验分支,不能把
  未模拟水作用的干态 DEM 曲线报告成水敏感性结果。
- 每组试件数量、调温方式、保温时间和异常值处理必须作为实验输入记录;模型
  不能用一个随机种子替代成组重复性。

## 荷载-变形数据契约

至少导出:

```text
time, upper_head_position, lower_head_position,
upper_reaction, lower_reaction, raw_deformation, temperature, sample_id
```

- 保存两个压头各自的反力和位置;最终曲线所用合力、相对位移、正负号和单位
  必须单独定义。
- 实验方法要求连续记录荷载-变形曲线并进行原点修正。DEM 同时保留原始曲线、
  修正原点和修正曲线,不得只保存峰值。
- 峰值清楚时,稳定度取修正曲线最大荷载,流值取该荷载对应的修正变形。
- 峰值不明显时,按当前方法规定的平移线构造修正点;不得用“峰值时原始位移”
  或旧脚本的固定后峰值比例代替。
- 马歇尔模数按所选版次以稳定度和流值计算,并保留两者原始单位与舍入规则。

## PFC5 映射

1. 弧形压头几何按所选标准/大型装置核对,禁止把拳头包的平面劈裂压板直接
   命名为马歇尔压头。
2. 空载运动探针验证墙 ID、轴向、对中、球座/约束等效和禁止转动条件。
3. 小颗粒接触探针验证压头-颗粒接触、摩擦和反力符号。
4. 试件调温和加载速率来自锁定的方法输入;Burger 参数必须与同一温度、速率
   下的实验响应标定。
5. 终止条件应允许完整识别当前方法所需的最大值或平台,不得直接沿用
   `dc_loadFac` 而不做曲线完整性审计。
6. 2D 模型必须声明面外厚度和力的换算;未经 3D/实验校准的 2D 反力不能直接
   报为规范稳定度。

## 交付字段

- 规范版次、T 0709-2025、成型方法和条款/印刷页定位;
- 试件类型、尺寸、密度、空隙率、调温和分组信息;
- 原始与修正荷载-变形曲线、稳定度、流值和马歇尔模数;
- 浸水/真空饱水分支是否实际执行;
- 重复性、异常值处理、失败模式和未通过的 PFC 运行门槛。
rea-analysis-optimizationmorluto/reaOptimize REA providers and shared analysis workflows for agent context, latency, CPU, and memory while preserving correctness and Evidence. Use for analysis bottlenecks and cache or query design; CI/test-suite optimization belongs to rea-ci-tests-audit.Stars: 472kUpdated Claude CodeCodexVerifiedInstall
rea-ci-tests-auditmorluto/reaAudit REA CI and test suites for correctness, fixture drift, false passes, and measured performance; use for suite or workflow investigations and efficiency changes, rather than ordinary feature testing or a single test failure.Stars: 472kUpdated Claude CodeCodexVerifiedInstall
rea-tool-designmorluto/reaAudit, investigate, design, or change REA investigation tools, CLI/MCP contracts, provider capabilities, and Evidence semantics.Stars: 472kUpdated Claude CodeCodexVerifiedInstall
ponytail-auditDietrichGebert/ponytailQuality audit of the whole repo: bugs, security, real load, missing tests, speed, and what to delete. Most important first.Stars: 196kUpdated Claude CodeCodexVerifiedInstall