Echo-aloha/asphalt-codex-skills-5 / skills/pfc-asphalt-mixture
pfc-asphalt-mixture
VerifiedBuild PFC 5.0 asphalt-mixture specimens with explicit aggregate objects, a declared homogenized-mastic or fine-particle abstraction, residual air voids, measured gradation conversion, contact-pair assignment, compaction, equilibrium, and mass-volume closure; use before Marshall, rutting, creep, or strength tests.
| File | Kind | Size |
|---|---|---|
| SKILL.md | skill md | 9.0 KB |
| agents/openai.yaml | config | 350 B |
| dependencies.json | config | 292 B |
| references/gradation.md | markdown | 3.3 KB |
| references/overview.md | markdown | 7.0 KB |
| scripts/minimal_specimen_smoke.p3dat | other | 718 B |
references/gradation.md
View on GitHub# 级配输入与体积转换
本参考不再分发任何标准级配表或“中值级配”。级配上下限、设计级配和验收条件
必须来自用户合法取得的当前适用规范、项目配合比或实测筛分数据,并记录来源、
版次和日期。不要把示例数值当成 AC-13、AC-16 或 AC-20 的默认输入。
## 用户输入模板
建议把实测数据保存为 UTF-8 CSV:
```csv
sieve_mm,passing_percent,source_id,measurement_date
<sieve>,<0_to_100>,<project_or_lab_record>,<YYYY-MM-DD>
```
至少核对:
- 筛孔按大到小排序,通过率随筛孔减小不得增加;
- 最大筛孔通过率、最小筛孔通过率和相邻差值均在物理合理范围;
- 每个数值的质量基准一致,并说明是实测、设计值还是规范边界;
- 物理粗细集料分界与 DEM 显式—均质化 cutoff 分开声明;
- 缩尺或截断后的级配重新归一化,并保留原始级配用于误差审计。
## JTG 3432-2024 来源门槛
对采用中国公路工程集料试验体系的项目,先锁定材料类别和方法,再导入数值:
- 粗集料筛分以 T 0302-2024 为来源入口;细集料筛分以 T 0327-2005 为
来源入口;填料按 T 0351 或 T 0356 的适用条件记录。
- 分档质量换算体积时,粗集料、细集料和填料分别记录实际采用的密度/吸水率
方法、材料状态和测定单位,不能仅写“按规范密度”。
- 针片状、棱角性、压碎、磨耗、磨光和高温稳定性等指标只用于约束形状/接触
假设和敏感性范围;没有宏观标定时,不得直接换算为 clump 模板或接触强度。
- JTG 3432-2024 是材料试验方法来源,不提供项目 AC-13/16/20 设计级配;设计
级配仍来自经批准的配合比、施工/设计文件或实测筛分记录。
## 体积级配到离散对象
对相邻筛孔 `i` 和 `i+1`,分档质量比例由用户输入的通过率差得到:
```text
fraction_i = passing_i - passing_(i+1)
```
随后按各档实测表观密度换算体积。若所有档使用同一密度,这只是明确记录的
简化假设,不应自动采用。目标固相体积应由试件总体积、目标空隙率、结合料/砂浆
体积及显式相定义共同闭合,而不是使用固定经验占比。
每个显式档的目标体积除以所选 ball、clump 或形状模板的实际体积,得到初始对象
数估计;最终对象数还需满足随机生成、边界裁剪、压实和质量—体积闭合。未显式
解析的细料、矿粉和结合料进入已声明的均质相,其质量与体积不能消失。
## 交付记录
输出应包含原始 CSV、清洗后 CSV、分档差值、密度来源、尺度映射、对象体积、
归一化误差和最终闭合误差。若用户没有提供合法来源的数值,只能交付空模板与
计算方法,不能代填标准表。
标准是否现行应从发布机构核验。试验规程的版本入口可参考交通运输部
[2025 年第 27 号公告](https://xxgk.mot.gov.cn/jigou/glj/202508/t20250822_4175218.html);
混合料设计/施工级配还应核对项目采用的相应现行规范,不能由本文件替代。
规范角色和方法链见
[`pfc5-asphalt-workflow/references/standards-method-map.md`](../../pfc5-asphalt-workflow/references/standards-method-map.md)。
Related skills
| Skill | Stars | Updated | Works with | Status | Install |
|---|---|---|---|---|---|
| finishing-a-development-branchobra/superpowersUse when implementation is complete, all tests pass, and you need to decide how to integrate the work | Stars: 322k | Updated | Claude CodeCodex | Verified | Install |
| systematic-debuggingobra/superpowersUse when encountering any bug, test failure, or unexpected behavior, before proposing fixes | Stars: 322k | Updated | Claude CodeCodex | Verified | Install |
| test-driven-developmentobra/superpowersUse when implementing any feature or bugfix, before writing implementation code | Stars: 322k | Updated | Claude CodeCodex | Verified | Install |
| skill-creatoranthropics/skillsCreate new skills, modify and improve existing skills, and measure skill performance. Use when users want to create a skill from scratch, edit, or optimize an existing skill, run evals to test a skill, benchmark skill performance with variance analysis, or optimize a skill's description for better triggering accuracy. | Stars: 198k | Updated | Claude CodeCodex | Verified | Install |